manualshive.com logo in svg

Keysight DSOX3012T, User Manual

The Keysight DSOX3012T is a high-performance digital storage oscilloscope designed for precision measurements in a variety of applications. For detailed instructions on how to utilize all the features and functions of this device, you can download the user manual for free from 88.208.23.73:8080.

Share
Download
background image

Triggers

11

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

175

 

a

Press the 

Arm A

 softkey, and turn the Entry knob to select the channel on 

which the arming edge will occur.

b

Press the 

Slope A

 softkey to specify which edge of the Arm A signal will arm 

the oscilloscope.

c

Press the 

Trigger B

 softkey, and turn the Entry knob to select the channel on 

which the trigger edge will occur.

d

Press the 

Slope B

 softkey to specify which edge of the Trigger B signal will 

trigger the oscilloscope.

Adjust the trigger level for the selected analog channel by turning the Trigger 

Level knob. Press the 

[Digital]

 key and select 

Thresholds

 to set the threshold level 

for digital channels. The value of the trigger level or digital threshold is 

displayed in the upper-right corner of the display.

5

Press the 

Back/Up key to return to the Trigger Menu.

6

Press the 

Delay

 softkey; then, turn the Entry knob to enter the delay time 

between the Arm A edge and the Trigger B edge.

7

Press the 

Nth Edge B

 softkey; then, turn the Entry knob to select the Nth edge of 

the Trigger B signal to trigger on.

Pulse Width Trigger

Pulse Width (glitch) triggering sets the oscilloscope to trigger on a positive or 

negative pulse of a specified width. If you want to trigger on a specific timeout 

value, use 

Pattern

 trigger in the Trigger Menu (see 

“Pattern Trigger"

on page 178).

1

Press the 

[Trigger]

 key.

2

In the Trigger Menu, press the 

Trigger

 softkey; then, turn the Entry knob to 

select 

Pulse Wid th

.

Back

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DSOX3012T

Raven CR7 Update Manual preview
CR7
Brand: Raven Pages: 17
Campbell SC932A Product Manual preview
SC932A
Brand: Campbell Pages: 12
Hacker PROGBOX Manual preview
PROGBOX
Brand: Hacker Pages: 2
J.P. SELECTA SE-100 Manual preview
SE-100
Brand: J.P. SELECTA Pages: 8
Haemonetics PCS 2 Manual preview
PCS 2
Brand: Haemonetics Pages: 134
Hadeco Smartdop 30EX Operation Manual preview
Smartdop 30EX
Brand: Hadeco Pages: 72
Wasp Clay Kit Original Instructions Manual preview
Clay Kit
Brand: Wasp Pages: 50
Gaspardo PI Use And Maintenance preview
PI
Brand: Gaspardo Pages: 44
Yamaha MU100 Manuel Du Propriétaire preview
MU100
Brand: Yamaha Pages: 178
Yamaha EMT-10 Manuel De L'Utilisateur preview
EMT-10
Brand: Yamaha Pages: 15
Additel 226 User Manual preview
226
Brand: Additel Pages: 107
Vaisala GMP251 Quick Start Manual preview
GMP251
Brand: Vaisala Pages: 2
EFX EFF523 Instructions For Use preview
EFF523
Brand: EFX Pages: 2
Pfeuffer 1520 9001 Operating Instructions Manual preview
1520 9001
Brand: Pfeuffer Pages: 32
WATSON INDUSTRIES AHRS-E304 Owner'S Manual preview
AHRS-E304
Brand: WATSON INDUSTRIES Pages: 17
Gastrodomus GA600BTV Installation - Use - Maintenance preview
GA600BTV
Brand: Gastrodomus Pages: 22
Bestway Backyard Cabin Manual preview
Backyard Cabin
Brand: Bestway Pages: 6
EXFO FOT-930 MaxTester Manual preview
FOT-930 MaxTester
Brand: EXFO Pages: 8

Brands by name

Popular brands

Load more brands