manualshive.com logo in svg

Keysight DSOX3012T, User Manual

The Keysight DSOX3012T is a high-performance digital storage oscilloscope designed for precision measurements in a variety of applications. For detailed instructions on how to utilize all the features and functions of this device, you can download the user manual for free from 88.208.23.73:8080.

Share
Download
background image

Triggers

11

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

181

 

OR Trigger

The OR trigger mode triggers when any one (or more) of the specified edges on 

analog or digital channels is found.

1

On the front panel, in the Trigger section, press the 

[Trigger]

 key.

2

In the Trigger Menu, press the 

Trigger

 softkey, and use the Entry knob to select 

OR

.

3

Press the 

Slope

 softkey and select rising edge, falling edge, either edge, or don't 

care. The selected slope is displayed in the upper-right corner of the display.

4

For each analog or digital channel you want to include in the OR trigger, press 

the 

Channel

 softkey to select the channel.

As you press the 

Channel

 softkey (or rotate the Entry knob), the channel you 

select is highlighted in the OR = line directly above the softkeys and in the 

upper-right corner of the display next to the OR gate symbol.

Adjust the trigger level for the selected analog channel by turning the Trigger 

Level knob. Press the 

[Digital]

 key and select 

Thresholds

 to set the threshold level 

for digital channels. The value of the trigger level or digital threshold is 

displayed in the upper-right corner of the display.

5

For each channel you select, press the 

Slope

 softkey and select   (Rising),   

(Falling),   (Either), or X (Don't Care). The selected slope is displayed above the 

softkeys.

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DSOX3012T

GE TruSat User Manual preview
TruSat
Brand: GE Pages: 43
GE Responder AED Service Manual preview
Responder AED
Brand: GE Pages: 37
GE Senographe DS Operator'S Manual preview
Senographe DS
Brand: GE Pages: 210
GE MAC 5000 Field Service Manual preview
MAC 5000
Brand: GE Pages: 160
GE MAC 1600 Service Manual preview
MAC 1600
Brand: GE Pages: 146
GE Dash 2500 Quick Manual preview
Dash 2500
Brand: GE Pages: 6
GE ApexPro Manual preview
ApexPro
Brand: GE Pages: 27
GE Voluson 730 Manual preview
Voluson 730
Brand: GE Pages: 4
Parker RC Series Maintenance Instructions preview
RC Series
Brand: Parker Pages: 5
Bacharach Fyrite INSIGHT Operating & Maintenance Instructions preview
Fyrite INSIGHT
Brand: Bacharach Pages: 31
Backyard Play Systems 4105 Instruction Manual preview
4105
Brand: Backyard Play Systems Pages: 52
Backyard Play Systems 4030 Instructions Manual preview
4030
Brand: Backyard Play Systems Pages: 19
Backyard Play Systems 4030 Manual preview
4030
Brand: Backyard Play Systems Pages: 44
Bacharach Monoxor III Specification Sheet preview
Monoxor III
Brand: Bacharach Pages: 2
Barco Coronis 5MP Mammo Brochure & Specs preview
Coronis 5MP Mammo
Brand: Barco Pages: 4
Barco CORONIS 1MP Installation & User Manual preview
CORONIS 1MP
Brand: Barco Pages: 167
Barco Color Coronis 2MP System Manual preview
Color Coronis 2MP
Brand: Barco Pages: 156
Barco Color Coronis 2MP Brochure & Specs preview
Color Coronis 2MP
Brand: Barco Pages: 12

Brands by name

Popular brands

Load more brands