Keysight DSOX3012T User Manual Download

Page: 233 / 530

233

Keysight InfiniiVision 3000T X-Series Oscilloscopes

User's Guide

14 Cursors

To make cursor measurements / 234
Cursor Examples / 237

Cursors are horizontal and vertical markers that indicate X-axis values and Y-axis

values on a selected waveform source. You can use cursors to make custom

voltage, time, phase, or ratio measurements on oscilloscope signals.

Cursor information is displayed in the right-side information area.

Cursors are not always limited to the visible display. If you set a cursor, then pan

and zoom the waveform until the cursor is off screen, its value will not be changed.

It will still be there when you return to its original location.

X Cursors

X cursors are vertical dashed lines that adjust horizontally and can be used to

measure time (s), frequency (1/s), phase (°), and ratio (%).

The X1 cursor is the short-dashed vertical line, and the X2 cursor is the

long-dashed vertical line.

When used with the FFT math function as a source, the X cursors indicate

frequency.

In XY horizontal mode, the X cursors display channel 1 values (Volts or Amps).

The X1 and X2 cursor values for the selected waveform source are displayed in the

softkey menu area.

The difference between X1 and X2 (

X) and 1/

X are displayed in the Cursors box

in the right-side information area.

Y Cursors

Y cursors are horizontal dashed lines that adjust vertically and can be used to

measure Volts or Amps, dependent on the channel

Probe Units

setting, or they can

measure ratios (%). When math functions are used as a source, the measurement

units correspond to that math function.

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands

Keysight DSOX3012T, User Manual

Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands