manualshive.com logo in svg

Keysight DSOX3012T, User Manual

The Keysight DSOX3012T is a high-performance digital storage oscilloscope designed for precision measurements in a variety of applications. For detailed instructions on how to utilize all the features and functions of this device, you can download the user manual for free from 88.208.23.73:8080.

Share
Download
background image

Measurements

15

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

271

 

•

The units for absolute threshold for each channel is set in the channel probe 

menu.

4

Press the 

Lower

 softkey; then, turn the Entry knob to set the lower measurement 

threshold value.

Increasing the lower value beyond the set middle value will automatically 

increase the middle value to be more than the lower value. The default lower 

threshold is 10% or 800 mV.

If threshold 

Type

 is set to 

%

, the lower threshold value can be set from 0% to 

98%.

5

Press the 

Middle

 softkey; then, turn the Entry knob to set the middle 

measurement threshold value.

The middle value is bounded by the values set for lower and upper thresholds. 

The default middle threshold is 50% or 1.20 V.

•

If threshold 

Type

 is set to 

%

, the middle threshold value can be set from 1% to 

99%.

6

Press the 

Upper

 softkey; then, turn the Entry knob to set the upper 

measurement threshold value.

Decreasing the upper value below the set middle value will automatically 

decrease the middle value to be less than the upper value. The default upper 

threshold is 90% or 1.50 V.

•

If threshold 

Type

 is set to 

%

, the upper threshold value can be set from 2% to 

100%.

TIP

Absolute threshold hints

•

Absolute thresholds are dependent on channel scaling, probe attenuation, and probe units. Always 

set these values first before setting absolute thresholds.

•

The minimum and maximum threshold values are limited to on-screen values.

•

If any of the absolute threshold values are above or below the minimum or maximum waveform 

values, the measurement may not be valid.

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DSOX3012T

PANDROL CD100 User And Maintenance Manual preview
CD100
Brand: PANDROL Pages: 36
Badger Basket CABANA Assembly Instructions Manual preview
CABANA
Brand: Badger Basket Pages: 7
Backyard Discovery ASPEN 6515 Owner'S Manual preview
ASPEN 6515
Brand: Backyard Discovery Pages: 53
Kärcher FRV 30 ME Original Instructions Manual preview
FRV 30 ME
Brand: Kärcher Pages: 88
ZOLL IVTM Physician'S Manual preview
IVTM
Brand: ZOLL Pages: 37
Wacker Neuson MP70 Operator'S Manual preview
MP70
Brand: Wacker Neuson Pages: 34
Wagan 2296 User Manual preview
2296
Brand: Wagan Pages: 4
Wachs TFS Manual preview
TFS
Brand: Wachs Pages: 22
Gaspardo M Use And Maintenance / Spare Parts preview
M
Brand: Gaspardo Pages: 88
Yanmar RT66 Operator'S Manual preview
RT66
Brand: Yanmar Pages: 49
Fagor MX1000 Operating Instruction preview
MX1000
Brand: Fagor Pages: 12
Baltic POSEIDON User Manual preview
POSEIDON
Brand: Baltic Pages: 68
H&S 2958 Operator'S & Parts Manual preview
2958
Brand: H&S Pages: 76
Park House Healthcare AMBIENCE Service Manual preview
AMBIENCE
Brand: Park House Healthcare Pages: 32
Össur QUICK-ALIGN Vari-Flex Instructions For Use Manual preview
QUICK-ALIGN Vari-Flex
Brand: Össur Pages: 36
Össur Patriot Collar Instructions For Use preview
Patriot Collar
Brand: Össur Pages: 2
Össur Unloader One Instructions For Use Manual preview
Unloader One
Brand: Össur Pages: 8
Martin Maxedia 4 User Manual preview
Maxedia 4
Brand: Martin Pages: 202

Brands by name

Popular brands

Load more brands