manualshive.com logo in svg

Keysight DSOX3012T, User Manual

The Keysight DSOX3012T is a high-performance digital storage oscilloscope designed for precision measurements in a variety of applications. For detailed instructions on how to utilize all the features and functions of this device, you can download the user manual for free from 88.208.23.73:8080.

Share
Download
background image

406

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

25

CAN/LIN Triggering and Serial Decode

 

In addition to the standard Time column, the CAN Lister contains these columns:
• ID — frame ID. Can be displayed as hex digits or symbolic information (see 

“Loading and Displaying CAN Symbolic Data"

on page 398).

• Type — frame type (RMT remote frame or Data).
• DLC — data length code.
• Data — data bytes. Can be displayed as hex digits or symbolic information.
• CRC — cyclic redundancy check.
• Errors — highlighted in red. Errors can be Acknowledge (Ack, A), Form (Fo), or 

Frame (Fr). Different kinds of errors can be combined like "Fo,Fr" in the above 

example.

Aliased data is highlighted in pink. When this happens, decrease the horizontal 

time/div setting and run again.

Searching for CAN Data in the Lister

The oscilloscope's search capability lets you search for (and mark) certain types of 

CAN data in the Lister. You can use the 

[Navigate]

 key and controls to navigate 

through the marked rows.

1

With CAN selected as the serial decode mode, press 

[Search]

.

2

In the Search Menu, press the 

Search

 softkey; then, turn the Entry knob to select 

Serial 1 or Serial 2 on which the CAN signal is being decoded.

3

Press 

Search for

; then, select from these options:

•

Frame ID

 — Finds remote or data frames matching the specified ID.

•

Data Frame ID

 — Finds data frames matching the specified ID.

•

Data Frame ID and Data

 — Finds data frames matching the specified ID and 

data.

•

Remote Frame ID

 — Finds remote frames with the specified ID.

•

Error Frame

 — Finds CAN active error frames.

•

Acknowledge Error

 — Finds the acknowledge bit if the polarity is incorrect.

•

Form Error

 — Finds reserved bit errors.

•

Stuff Error

 — Finds 6 consecutive 1s or 6 consecutive 0s, while in a non-error 

or non overload frame.

•

CRC Field Error

 — Finds when the calculated CRC does not match the 

transmitted CRC.

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DSOX3012T

Daga AB Directions For Use Manual preview
AB
Brand: Daga Pages: 24
DAF DAVIE XDc II Quick Start Manual preview
DAVIE XDc II
Brand: DAF Pages: 68
Mandam MCH Series Instruction Manual preview
MCH Series
Brand: Mandam Pages: 9
Jackco 852 User Manual preview
852
Brand: Jackco Pages: 6
Gary Machinery 3354 Instruction Manual preview
3354
Brand: Gary Machinery Pages: 14
MAGIC FX CO2JET II User And Installation Manual preview
CO2JET II
Brand: MAGIC FX Pages: 25
U-Line S-11303 Quick Start Manual preview
S-11303
Brand: U-Line Pages: 3
U-Line H-3736 Installation Instructions preview
H-3736
Brand: U-Line Pages: 2
U-Line H-5334 Quick Start Manual preview
H-5334
Brand: U-Line Pages: 9
U-Line Green Machine H-3518 Instructions preview
Green Machine H-3518
Brand: U-Line Pages: 3
Posture Pump Disc Hydrator Instructions preview
Disc Hydrator
Brand: Posture Pump Pages: 2
Electro-Music Klee Sequencer Building Instructions preview
Klee Sequencer
Brand: Electro-Music Pages: 120
habitat et jardin PZ0001A Assembly Instruction preview
PZ0001A
Brand: habitat et jardin Pages: 4
NTN K-N25 Series Instruction Manual preview
K-N25 Series
Brand: NTN Pages: 19
Baileigh RDB-050 Operator'S Manual preview
RDB-050
Brand: Baileigh Pages: 39
Ralph Lauren Willoughby XL Assembly Instructions preview
Willoughby XL
Brand: Ralph Lauren Pages: 2
Axess sepro ROBOTIQUE User Manual preview
sepro ROBOTIQUE
Brand: Axess Pages: 44
M-Audio CODE 25 Quick Start Manual preview
CODE 25
Brand: M-Audio Pages: 40

Brands by name

Popular brands

Load more brands