manualshive.com logo in svg

Keysight DSOX3012T, User Manual

The Keysight DSOX3012T is a high-performance digital storage oscilloscope designed for precision measurements in a variety of applications. For detailed instructions on how to utilize all the features and functions of this device, you can download the user manual for free from 88.208.23.73:8080.

Share
Download
background image

410

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

25

CAN/LIN Triggering and Serial Decode

 

1

Press 

[Trigger]

.

2

In the Trigger Menu, press the 

Trigger Type

 softkey; then, turn the Entry knob to 

select the serial slot (Serial 1 or Serial 2) on which the CAN signal is being 

decoded.

3

Press the 

Trigger on:

 softkey; then, turn the Entry knob to select the trigger 

condition:

•

Sync

 (Sync Break) — The oscilloscope triggers on the rising edge at the Sync 

Break exit of the LIN single-wire bus signal that marks the beginning the 

message frame.

•

ID

 (Frame ID) — The oscilloscope triggers when a frame with an ID equal to 

the selected value is detected. Use the 

Entry

 knob to select the value for the 

Frame ID.

•

ID & Data

 (Frame ID and Data) — The oscilloscope triggers when a frame with 

an ID and data equal to the selected values is detected. When triggering on 

a frame ID and data:

•

To select the frame ID value, press the 

Frame ID

 softkey, and use the 

Entry

 

knob.

Note that you can enter a "don't care" value for the frame ID and trigger 

on data values only.

•

To set up the number of data bytes and enter their values (in hexadecimal 

or binary), use the remaining softkeys.

•

Parity Error

 — The oscilloscope triggers on parity errors.

•

Checksum Error

 — The oscilloscope triggers on checksum errors.

When a LIN description file (*.ldf) is loaded (recalled) into the oscilloscope (see 

“Loading and Displaying LIN Symbolic Data"

on page 409), you can trigger on:

•

Frame (Symbolic)

 — a symbolic frame value.

Sync

Break

Identifier

Break

Sync Break Exit

Sync
Field

Checksum

Field

Data

Fields

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DSOX3012T

Datavideo HS-600 Instruction Manual preview
HS-600
Brand: Datavideo Pages: 50
Waterous Eclipse Installation, Operation And Maintenance Manual preview
Eclipse
Brand: Waterous Pages: 90
Campbell SC105 Product Manual preview
SC105
Brand: Campbell Pages: 14
DanMedical D-MAS HyperSat 2540 Instructions For Use Manual preview
D-MAS HyperSat 2540
Brand: DanMedical Pages: 103
Tascam US-1200 Quick Start Manual preview
US-1200
Brand: Tascam Pages: 8
B-K lighting Union Bollard Installation Instructions preview
Union Bollard
Brand: B-K lighting Pages: 5
B-K lighting RE1 Installation Instructions preview
RE1
Brand: B-K lighting Pages: 4
B-K lighting PS Installation Instructions preview
PS
Brand: B-K lighting Pages: 3
Dawn 1500 Assembly And Operation Manual preview
1500
Brand: Dawn Pages: 8
BACtrack VIO User Manual preview
VIO
Brand: BACtrack Pages: 13
Badgematic FLEXI Manual preview
FLEXI
Brand: Badgematic Pages: 28
BACtrack Select S80 Product Specifications preview
Select S80
Brand: BACtrack Pages: 2
MADRIX STELLA Quick Start Manual & Technical Manual preview
STELLA
Brand: MADRIX Pages: 28
BACTcontrol microLAN Software Manual preview
microLAN
Brand: BACTcontrol Pages: 28
Backyard Products 4030 Assembly Instructions Manual preview
4030
Brand: Backyard Products Pages: 98
Baker D30R User Manual preview
D30R
Brand: Baker Pages: 82
Rain-Flo Irrigation 2370 Operating Manual preview
2370
Brand: Rain-Flo Irrigation Pages: 16
Quivogne SCD Operating, Maintenance & Spare Parts Book preview
SCD
Brand: Quivogne Pages: 13

Brands by name

Popular brands

Load more brands