manualshive.com logo in svg

Keysight DSOX3012T, User Manual

The Keysight DSOX3012T is a high-performance digital storage oscilloscope designed for precision measurements in a variety of applications. For detailed instructions on how to utilize all the features and functions of this device, you can download the user manual for free from 88.208.23.73:8080.

Share
Download
background image

Manchester/NRZ Triggering and Serial Decode

30

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

475

 

In the NRZ Settings Menu:

a

Press the 

Polarity

 softkey and select the NRZ signal's logic type:

•

High — specifies that a positive voltage is used to encode a bit value of 

logic 1 (and a negative voltage encodes a bit value of logic 0).

•

Low — specifies that a negative voltage is used to encode a bit value of 

logic 1 (and a positive voltage encodes a bit value of logic 0).

b

Press the 

Bit Order

 softkey and select the bit order, either most significant bit 

first (

MSB

) or least significant bit first (

LSB

).

The selected order is used when displaying data in the serial decode 

waveform and in the Lister.

c

Press the 

Idle State

 softkey and choose the idle state of the NRZ bus, either 

Low or High.

d

Press the 

Idle Bits

 softkey and enter the minimum idle time/inter-frame gap 

time of the NRZ bus in terms of the bit width.

Framing is determined by idle time.

e

Use the 

Decode Base

 softkey to select between hexadecimal, unsigned 

decimal, or ASCII display of the decoded data.

The decode base setting is used for the display of the data field in both the 

decode line and in the Lister.

f

Press the 

Back/Up key to return to the Serial Decode Menu.

NRZ Triggering

To set up the oscilloscope to capture a NRZ signal, see 

“Setup for NRZ 

Signals"

on page 473.

To set up a NRZ signal:

1

Press 

[Trigger]

.

2

In the Trigger Menu, press the 

Trigger Type

 softkey; then, select the NRZ decode 

(Serial 1 or Serial 2).

Back

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DSOX3012T

ABB SACE Tmax XT Series Manual preview
SACE Tmax XT Series
Brand: ABB Pages: 11
Palazzetti P1 Installation Instructions, Use And Maintenance preview
P1
Brand: Palazzetti Pages: 112
jablotron JA-65ST Quick Start Manual preview
JA-65ST
Brand: jablotron Pages: 2
Taylor 358 Service Manual preview
358
Brand: Taylor Pages: 60
TANDBERG Model 5 Service Manual preview
Model 5
Brand: TANDBERG Pages: 23
Backyard Play Systems 4431 Assembly Instructions Manual preview
4431
Brand: Backyard Play Systems Pages: 73
Rane SM26 Operating & Service Manual preview
SM26
Brand: Rane Pages: 6
Rane MP 4 Operation Manual preview
MP 4
Brand: Rane Pages: 27
Ranger Products RD-18G Installation And Operation Manual preview
RD-18G
Brand: Ranger Products Pages: 6
Rane SEVENTY Service Manual preview
SEVENTY
Brand: Rane Pages: 88
Haag-Streit AT 900 Instructions For Use Manual preview
AT 900
Brand: Haag-Streit Pages: 21
Quadro mdb MOBIL Construction Manual preview
MOBIL
Brand: Quadro mdb Pages: 11
Handicare MiniLift160 Classic Service Manual preview
MiniLift160 Classic
Brand: Handicare Pages: 28
Hands Free Farm RANGER User Manual preview
RANGER
Brand: Hands Free Farm Pages: 24
i-Optik CV-7800 Operator'S Manual preview
CV-7800
Brand: i-Optik Pages: 75
Tar River SLC Series Operator'S Manual preview
SLC Series
Brand: Tar River Pages: 26
ZOLL M Series CCT Configuration Manual preview
M Series CCT
Brand: ZOLL Pages: 38
ZOLL aed pro Service Manual preview
aed pro
Brand: ZOLL Pages: 36

Brands by name

Popular brands

Load more brands