manualshive.com logo in svg

Keysight DSOX3012T, User Manual

The Keysight DSOX3012T is a high-performance digital storage oscilloscope designed for precision measurements in a variety of applications. For detailed instructions on how to utilize all the features and functions of this device, you can download the user manual for free from 88.208.23.73:8080.

Share
Download
background image

504

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

32

SENT Triggering and Serial Decode

 

SENT Serial Decode

To set up the oscilloscope to capture SENT signals, see 

“Setup for SENT 

Signals"

on page 497.

To set up SENT serial decode:

1

Press 

[Serial]

 to display the Serial Decode Menu.

2

If the decode line does not appear on the display, press the 

[Serial]

 key to turn it 

on.

3

If the oscilloscope is stopped, press the 

[Run/Stop]

 key to acquire and decode 

data.

You can use the horizontal 

Zoom

 window for easier navigation of the acquired data.

NOTE

If the setup does not produce a stable trigger, the SENT signals may be slow enough that the 

oscilloscope is AutoTriggering. Press the 

[Mode/Coupling]

 key, then press the 

Mode

 softkey 

to set the trigger mode from 

Auto

 to 

Normal

.

NOTE

To display SENT serial decode, see 

“SENT Serial Decode"

on page 504.

NOTE

For SENT triggering setup see 

“SENT Triggering"

on page 502.

NOTE

If the setup does not produce a stable trigger, the SENT signals may be slow enough that the 

oscilloscope is AutoTriggering. Press the 

[Mode/Coupling]

 key, then press the 

Mode

 softkey 

to set the trigger mode from 

Auto

 to 

Normal

.

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DSOX3012T

MAHLE MCX-2 Operation Manual preview
MCX-2
Brand: MAHLE Pages: 21
OMCA 760 Use And Maintenance Manual preview
760
Brand: OMCA Pages: 36
Salford 699 Assembly And Parts Manual preview
699
Brand: Salford Pages: 64
Gaspardo SP SPRINT Manual preview
SP SPRINT
Brand: Gaspardo Pages: 16
Gastrodomus PH100 Installation, Operating And Service Instructions preview
PH100
Brand: Gastrodomus Pages: 4
HANYOUNG NUX HL Series Instruction Manual preview
HL Series
Brand: HANYOUNG NUX Pages: 2
Gastrodomus CL Instructions For Use And Maintenance Manual preview
CL
Brand: Gastrodomus Pages: 39
Latham 309 Installation Manual preview
309
Brand: Latham Pages: 4
SafeWaze LATITUDE Manual preview
LATITUDE
Brand: SafeWaze Pages: 23
LAPPSET Promenade Installation Instructions Manual preview
Promenade
Brand: LAPPSET Pages: 16
Magma ONIX Operation And Maintenance Manual preview
ONIX
Brand: Magma Pages: 16
Native Instruments TRAKTOR KONTROL S4 User Manual preview
TRAKTOR KONTROL S4
Brand: Native Instruments Pages: 86
Native Instruments Maschine Reference Manual preview
Maschine
Brand: Native Instruments Pages: 245
Taylor C712 Operator Training preview
C712
Brand: Taylor Pages: 41
Raven RS1 Guidance And Steering Installation Manual preview
RS1
Brand: Raven Pages: 48
Pacific Solana Assembly Instructions Manual preview
Solana
Brand: Pacific Pages: 16
JBSYSTEMS Light SE100 Operation Manual preview
SE100
Brand: JBSYSTEMS Light Pages: 17
VADDIO OneLINK Bridge Installation Manual preview
OneLINK Bridge
Brand: VADDIO Pages: 58

Brands by name

Popular brands

Load more brands