Keysight DSOX3012T User Manual Download

Page: 89 / 530

Keysight InfiniiVision 3000T X-Series Oscilloscopes

User's Guide

4 FFT Spectral Analysis

FFT is used to compute the fast Fourier transform using analog input channels or a

lower math function. FFT takes the digitized time record of the specified source

and transforms it to the frequency domain. When the FFT function is selected, the

FFT spectrum is plotted on the oscilloscope display as magnitude in dBV versus

frequency. The readout for the horizontal axis changes from time to frequency

(Hertz) and the vertical readout changes from volts to dB.

Use the FFT function to find crosstalk problems, to find distortion problems in

analog waveforms caused by amplifier non-linearity, or for adjusting analog filters.

To display a FFT waveform:

Press the

[FFT]

key.

•

Source 1

— selects the source for the FFT.

•

Display

— selects one of these FFT waveform display modes:

•

Normal

— this is the FFT waveform without any averaging or hold functions

applied. This is how FFT math function waveforms are displayed.

•

Averaged Value

— the FFT waveform is averaged the selected number of

times. Averages are calculated using a "decaying average" approximation,

where:

next_average = current_a (new_data - current_average)/N

Where N starts at 1 for the first acquisition and increments for each

following acquisition until it reaches the selected number of averages,

where it holds.

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands

Keysight DSOX3012T, User Manual

Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands