Keysight DSOX3012T User Manual Download | Manualshive

Page: 171 / 530

background image

Triggers

11

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

171

You can also adjust the trigger level using the touchscreen. See

Trigger Menu, Change the Trigger Mode, and Open the Trigger Level Dialog"

You can push the Trigger Level knob to set the level of all displayed analog

channels to the waveform's 50% value. If AC coupling is used, pushing the Trigger

Level knob sets the trigger level to about 0 V.

When High and Low (dual) trigger levels are used (as with the Rise/Fall Time and

Runt triggers, for example), pushing the Level knob toggles between high and low

level adjustment.

The position of the trigger level for the analog channel is indicated by the trigger
level icon (if the analog channel is on) at the far left side of the display. The

value of the analog channel trigger level is displayed in the upper-right corner of

the display.

The trigger level for a selected digital channel is set using the threshold menu in

the Digital Channel Menu. Press the

[Digital]

key on the front panel, then press the

Thresholds

softkey to set the threshold level (TTL, CMOS, ECL, or user defined) for

the selected digital channel group. The threshold value is displayed in the

upper-right corner of the display.

The line trigger level is not adjustable. This trigger is synchronized with the power

line supplied to the oscilloscope.

Forcing a Trigger

The

[Force Trigger]

key causes a trigger (on anything) and displays the acquisition.

This key is useful in the Normal trigger mode where acquisitions are made only

when the trigger condition is met. In this mode, if no triggers are occurring (that is,

the "Trig'd?" indicator is displayed), you can press

[Force Trigger]

to force a trigger

and see what the input signals look like.

In the Auto trigger mode, when the trigger condition is not met, triggers are forced

and the "Auto?" indicator is displayed.

T

NOTE

You can also change the trigger level of all channels by pressing

[Analyze] > Features

and

then selecting

Trigger Levels

.

«
...
169
170
171
172
173
...
»

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DSOX3012T

Brand: Balanced Body Pages: 4

Brand: Makita Pages: 17

Brand: Makita Pages: 13

Brand: Cadman Pages: 66

Movie FL Black E27 Flaps

Brand: Qazqa Pages: 2

Brand: Velocitek Pages: 81

ABS-Lock X-Flat

Brand: ABS Pages: 8

ABS-Lock X-DURCH

Brand: ABS Pages: 8

Brand: ABS Pages: 8

Brand: AcceleDent Pages: 3

Brand: Zero 88 Pages: 32

Brand: Jackco Pages: 6

Brand: Olsen Pages: 4

Dominator Series

Brand: Falcon Pages: 31

Brand: Fakir Pages: 22

Tablet1000 Series

Brand: Hantek Pages: 98

Brand: IDS Pages: 2

Brand: NatureZap Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands