manualshive.com logo in svg

Keysight DSOX3012T, User Manual

The Keysight DSOX3012T is a high-performance digital storage oscilloscope designed for precision measurements in a variety of applications. For detailed instructions on how to utilize all the features and functions of this device, you can download the user manual for free from 88.208.23.73:8080.

Share
Download
background image

172

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

11

Triggers

 

Edge Trigger

The Edge trigger type identifies a trigger by looking for a specified edge (slope) 

and voltage level on a waveform. You can define the trigger source and slope in 

this menu. The trigger type, source, and level are displayed in the upper-right 

corner of the display.

1

On the front panel, in the Trigger section, press the 

[Trigger]

 key.

2

In the Trigger Menu, press the 

Trigger

 softkey, and use the Entry knob to select 

Edge

.

3

Select the trigger source:

•

Analog channel, 

1

 to the number of channels

•

Digital channel (on mixed-signal oscilloscopes), 

D0

 to the number of digital 

channels minus one.

•

External

 — triggers on the EXT TRIG IN signal.

•

Line

 — triggers at the 50% level of the rising or falling edge of the AC power 

source signal.

•

WaveGen

 — triggers at the 50% level of the rising edge of the waveform 

generator output signal. (Not available when the DC, Noise, or Cardiac 

waveforms are selected.)

•

WaveGen Mod (FSK/FM)

 — when waveform generator FSK or FM modulation is 

used, triggers at the 50% level of the rising edge of the modulating signal.

You can choose a channel that is turned off (not displayed) as the source for the 

edge trigger.

The selected trigger source is indicated in the upper-right corner of the display 

next to the slope symbol:

•

1

 through 

4

 = analog channels.

•

D0

 through 

Dn

 = digital channels.

•

E

 = External trigger input.

•

L

 = Line trigger.

•

W

 = Waveform generator.

4

Press the 

Slope

 softkey and select:

•

Rising

 edge.

•

Falling

 edge.

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DSOX3012T

Jaga OXRE.015 Service Manual preview
OXRE.015
Brand: Jaga Pages: 32
Raytec VARIO2 series Full Installation And Setup Manual preview
VARIO2 series
Brand: Raytec Pages: 60
Jata hogar MOSQUITOTRAP MIE5 Manual preview
MOSQUITOTRAP MIE5
Brand: Jata hogar Pages: 20
StarDental Titan S Instruction Manual preview
Titan S
Brand: StarDental Pages: 2
USC K-VALVE Operator'S Manual preview
K-VALVE
Brand: USC Pages: 29
BendPak Blue Bullet 1302-BAS Operation And Service Manual preview
Blue Bullet 1302-BAS
Brand: BendPak Pages: 68
Buyers 8891102 Installation Instructions preview
8891102
Brand: Buyers Pages: 2
Drive 10274 Assembly Instructions preview
10274
Brand: Drive Pages: 2
TECALEMIT DE 7288/2005 Installation Operation & Maintenance preview
DE 7288/2005
Brand: TECALEMIT Pages: 19
OAKWORKS Clinician Premiere Series Instruction Manual preview
Clinician Premiere Series
Brand: OAKWORKS Pages: 29
Aeware In.pix User Manual preview
In.pix
Brand: Aeware Pages: 36
Tascam MiNiSTUDIO PERSONAL US-32 Manual preview
MiNiSTUDIO PERSONAL US-32
Brand: Tascam Pages: 11
Accelerated Care Plus OMNISTIM FX2 CYCLE/WALK User Manual preview
OMNISTIM FX2 CYCLE/WALK
Brand: Accelerated Care Plus Pages: 30
g-lites 600SZ User Manual preview
600SZ
Brand: g-lites Pages: 24
T3 Innovation Coax Clarifier TCC200 User Manual preview
Coax Clarifier TCC200
Brand: T3 Innovation Pages: 39
Maschio PITAGORA INLINE Operator'S Manual preview
PITAGORA INLINE
Brand: Maschio Pages: 100
R.V.R. Electronica SDC200/RDS User Manual preview
SDC200/RDS
Brand: R.V.R. Electronica Pages: 60
LNS Eco Load S2 Instruction Manual preview
Eco Load S2
Brand: LNS Pages: 112

Brands by name

Popular brands

Load more brands