manualshive.com logo in svg

Keysight DSOX3012T, User Manual

The Keysight DSOX3012T is a high-performance digital storage oscilloscope designed for precision measurements in a variety of applications. For detailed instructions on how to utilize all the features and functions of this device, you can download the user manual for free from 88.208.23.73:8080.

Share
Download
background image

350

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

22

Utility Settings

 

To set the date and time, or to view the current date and time:

1

Press 

[Utility] > Options > Clock

.

2

Press the 

Year

, 

Month

, 

Day

, 

Hour

 or 

Minute

 softkey; then, rotate the Entry knob to 

set to the desired number.

The hours are shown in the 24-hour format. So 1:00 PM is hour 13.

The real-time clock only allows selection of valid dates. If a day is selected and the 

month or year is changed so the day is invalid, the day is automatically adjusted.

Setting the Rear Panel TRIG OUT Source

You can choose the source of the TRIG OUT connector on the rear panel of the 

oscilloscope:

1

Press 

[Utility] > Options > Rear Panel

.

2

In the Rear Panel Menu, press 

Trig Out

; then, turn the Entry knob to select from:

•

Triggers

— Each time the oscilloscope triggers, a rising edge occurs on 

TRIG OUT. The rising edge is delayed 30 ns from the oscilloscope's trigger 

point. The output level is 0-5 V into an open circuit, and 0-2.5 V into 50

Ω

. 

See 

Chapter 11

, “Triggers,” starting on page 169.

•

Mask

— The pass/fail status is evaluated periodically. When the evaluation of 

the testing period results in a failure, the trigger output pulses high (+5 V). 

Otherwise, the trigger output remains at low (0 V). See 

Chapter 16

, “Mask 

Testing,” starting on page 275.

•

Waveform Generator Sync Pulse

— All of the waveform generator output 

functions (except DC, Noise, and Cardiac) have an associated Sync signal:

The Sync signal is a TTL positive pulse that occurs when the waveform rises 

above zero volts (or the DC offset value).

See 

Chapter 19

, “Waveform Generator,” starting on page 301.

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DSOX3012T

GE b30 User'S Reference Manual preview
b30
Brand: GE Pages: 242
GE ATS1290 Instruction Manual preview
ATS1290
Brand: GE Pages: 24
Balanced Body Allegro How To Assemble preview
Allegro
Brand: Balanced Body Pages: 3
C.M.O FL Series Instruction And Maintenance Manual preview
FL Series
Brand: C.M.O Pages: 10
DANLERS CEFL PIR Quick Start Manual preview
CEFL PIR
Brand: DANLERS Pages: 2
Haas Automation ST Manual preview
ST
Brand: Haas Automation Pages: 26
EAW UX8800 Quick Start Manual preview
UX8800
Brand: EAW Pages: 2
abc 907 Instructions For Use Manual preview
907
Brand: abc Pages: 28
Hantek Tablet1000 Series User Manual preview
Tablet1000 Series
Brand: Hantek Pages: 98
M-Audio Ozone User Manual preview
Ozone
Brand: M-Audio Pages: 48
M-Audio FireWire 410 Quick Start Manual preview
FireWire 410
Brand: M-Audio Pages: 19
M-Audio Fast Track Pro User Manual preview
Fast Track Pro
Brand: M-Audio Pages: 17
M-Audio MidAir User Manual preview
MidAir
Brand: M-Audio Pages: 18
M-Audio X-Session Guía De Inicio Rápido preview
X-Session
Brand: M-Audio Pages: 12
M-Audio X-Session User Manual preview
X-Session
Brand: M-Audio Pages: 20
Focusrite Audio Engineering Novation Launchkey Mini User Manual preview
Novation Launchkey Mini
Brand: Focusrite Audio Engineering Pages: 36
Vitax Supaturf Operator'S Manual preview
Supaturf
Brand: Vitax Pages: 12
DAN NTP TECHNOLOGY DAD Thunder Core 256 Installation Manual preview
NTP TECHNOLOGY DAD Thunder Core 256
Brand: DAN Pages: 16

Brands by name

Popular brands

Load more brands