Keysight M9360A Service Manual Download | Manualshive

Page: 12 / 43

background image

Getting Started

Hardware Requirements

Topic

Requirements

Chassis

Host controller

A PXI or PXI Express embedded controller or remote controller (external PC connected to the chassis
by a PCI-to-PXI interface) is required.

Embedded
controller

Agilent M9036A or an embedded controller that meets the following requirements:

l

PXIe system controller (PXI-1 embedded controllers are not compatible)

l

Utilize a 2x8, 4x4, or 1x4 PXIe system slot link configuration.

l

Run one of the operating systems listed in System Requirements (above).

Remote controller

(for Agilent M9018A chassis use only) Agilent M9021 Cable Interface x8 with one of the following PC
interface options:

l

Agilent

PCIe ExpressCard Adaptor x1, with cable (for a laptop PC)

l

Agilent

PCIe Desktop Adaptor x8, with cable (for desktop PCs)

Or an equivalent remote controller using a PC running one of the operating systems listed in System
Requirements (above).

Power up the Controller

If you are using a remote controller and you have installed the interface cable, you must power up

the chassis BEFORE you power up the PC. When you power down your chassis, Shut Down the PC
BEFORE you power down the chassis.

If you are using an embedded controller, complete the following steps:

1. Install the embedded controller module into the compatible chassis. The Agilent M9036A PXIe Embedded

Controller and Agilent M9018A PXIe Chassis are recommended. Please refer to the embedded controller
and chassis documentation for further details.

2. Connect peripherals (mouse, keyboard, monitor).

3. Power up the chassis.

Software Installation Overview

This installation includes the following:

l

Agilent IO Libraries Suite (IOLS), which includes the Agilent Connections Expert. This software is included
with your shipment (CD part number E2094-60003), and is also available at

www.agilent.com/find/iosuite

This software must be installed first.

Version 16.3.16603.3 (or newer) of the Agilent IO Libraries Suite is required.

l

Instrument software, which includes the SFP, device drivers (IVI-C, IVI-COM, and LabVIEW G) and doc-
umentation for the M9392A Vector Signal Analyzer. This software is included with your shipment (CD part
number M9392-10002), and is also available at

www.agilent.com/find/M9392A

.

1. Install the Agilent IO Libraries Suite from the Agilent IO Libraries Suite CD (E2094-60003) provided in

your ship kit. Follow the installer prompts to install the IO libraries.

2. Install the M9360A product software:

a. Using the Agilent M9392A PXI Vector Signal Analyzer Software and Product Information CD

(M9392-10002), launch the installer.

b. Follow the installer prompts. Choose a "Complete" installation to install all software and doc-

umentation, or a "Custom" installation to select from a listing of modules and other features.

Agilent M9360A PXI Attenuator/Preselector Service Guide

11

«
...
10
11
12
13
14
...
»

Summary of Contents for M9360A












































Reviews:

No comments

Related manuals for M9360A

Brand: J4C Pages: 4

Brand: ABB Pages: 6

Brand: KELCO Pages: 36

Brand: FAAC Pages: 32

Brand: Samson Pages: 2

Brand: Rachio Pages: 2

Brand: Tamas Pages: 12

Brand: Samson Pages: 6

Brand: DSEGenset Pages: 74

Brand: ITALFARAD Pages: 32

Brand: DS Produkte Pages: 4

Brand: GEM Pages: 56

Brand: Lunt Solar Systems Pages: 4

Synergy SGY-101

Brand: Fairford Pages: 20

Brand: Varian Pages: 37

Heat Control System

Brand: ORTAL Pages: 20

Brand: Haiwell Pages: 18

Brand: Pro-face Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands