background image

MODEL #A2000 – 2,000LB (907KG) WINCH

TABLE Of CONTENTS

Table of ConTenTs

Introduction ..................................... 1

Accessories ...............................................1

This Manual ...............................................1

Safety Definitions ............................ 1
Important Safety Instructions ......... 2
Controls and Features ..................... 4
Installation ...................................... 5

Mount the Winch .......................................5

Winch Assembly - Generic Install ...............5

Mount the Contactor ..................................6

Install Handlebar Mounted 

Mini Rocker Switch ....................................6

Mount the Hand Remote Socket .................6

Wiring the Winch .......................................7

Winch Wiring Diagram ...............................8

Motor End Terminal Rotation ......................8

Controller Wiring Diagram ..........................9

Cable Hook Stopper Installation and Use ....9

General Tips for Safe Operation ................10

Self Recovery ..........................................10

Winching Techniques  ..............................11

Snow Plow Usage ....................................12

Maintenance ................................. 12

Motor ......................................................12

Lubrication ..............................................12

Cable Assembly Replacement ..................12

Specifications ............................... 13

Performance: ...........................................13

Parts Diagram..........................................14

Parts List .................................................15

Troubleshooting ............................ 16
Warranty ....................................... 17

Contact Information .................................18

Summary of Contents for A2000

























Reviews: