KFI A3000 Operator'S Manual Download

Page: 20 / 24

MODEL #A3000 – 3,000LB (1361KG) WINCH

TROUBLESHOOTING

TroubleshooTInG

Problem

Cause

Solution

Motor does not run,
Contactor makes a click
sound.

Incorrect Wiring

Check Winch Wiring Diagram, make sure all wires
are correctly connected.

Incorrect Wiring

Hand Remote / Mini Rocker Switch wires must be
connected green to green and black to black.

Loose battery cable connections

Hand tighten nuts on all cable connections.

Motor Issue

Contact KFI Technical Support

Water has entered motor

Allow to drain and dry. Run in short burst with
load until completely dry.

Brake Spring installed backwards

Contact KFI Technical Support.

Motor does not run, NO
click sound from Contactor.

Incorrect Wiring

Check Winch Wiring Diagram, make sure all wires
are correctly connected.

Switch Ignition Wire

Check connection to an ignition fed source. Must
supply 12V with the key on and vehicle running.

Contactor malfunctioning

Contact KFI Technical Support.

Switch malfunctioning

Contact KFI Technical Support.

Motor runs, Spool turns in
one direction only.

Incorrect Wiring

Check wiring diagram, verify switch wires (black/
green) are properly connected and making good
contact.

Defective or stuck Contactor

Tap contactor to loosen plungers.

Defective Switch assembly

Replace Switch assembly.

Contactor malfunctioning

Contact KFI Technical Support.

Motor runs, Spool does
NOT turn.

Clutch not engaged

Rotate Clutch Cap to Engage.

Broken Coupler / stripped Shaft

Replace Coupler or Shaft

Spool turns, but no
movement from Cable

Cable not attached to Spool

Contact KFI Technical Support.

Motor runs slowly or
without normal power.

Insufficient current or voltage.

The battery is weak, recharge. Run winch with
vehicle motor running (battery should have a
strong charge).

Loose or corroded battery cable
connections

Clean, tighten, or replace.

Worn Brushes

Replace with End-Cap Kit (#SE-A-CAPKIT)
Contact KFI Technical Support.

Motor overheating

Winch running time too long

Allow winch to cool down periodically.

For further support, contact:

KFI Tech Support

Mon-Thr 8:00 AM - 5:00 PM (CST/CDT)
Fri 7:00 AM - 1:00PM (CST/CDT)
Toll Free: 1-877-346-2050
tech@kfiproducts.com

KFI Products Website Support:

Common installation, maintenance, and troubleshooting
guides are available on our website.

https://www.kfiproducts.com/support.html

Summary of Contents for A3000

























Search results

Summary of Contents for A3000

Reviews:

Related manuals for A3000

Brands by name

Popular brands

KFI A3000, Operator'S Manual

Search results

Summary of Contents for A3000

Reviews:

Related manuals for A3000

Brands by name

Popular brands