background image

8. Operation

DRILLING

  

  

  

  

10

Keep a firm grip of the auger at all times on a wide stance and by holding the handle with 

both hands.

A sudden jolt may occur on the auger when the drill has hit stones, tree roots or debris 

under the ground.  Always hold the auger securely and firmly to keep the auger under 

control.

Start drilling with half-throttle and gradually increse the engins speed to ensure smooth 

drilling into the ground.

If the drill is caught in the ground and cannot be pulled out, stop the engine and rotate the 

auger counter-clockwise.

9. Maintenance

E

NI

G

NE

TI

N

NI

A

M

• Before cleaning, inspecting or repairing the unit, make sure that the engine has stopped and is cool.

• Use protective gloves whenever inspecting, removing and installing the drill.

MAINTENANCE CHART

Every

Eve

ry

Eve

ry

25

50

100

       System/components

         P

rocedur

e

Befor

e

hours hours hours

                 

 Note

use

after after after

fuel leaks, fuel spillage

wipe out

fuel tank, air filter, fuel filter

inspect/clean

replace, if necessary

r

o

t

e

r

u

b

r

a

c

 

e

c

a

l

p

e

r

g

n

it

s

u

j

d

a

 

e

e

s

idle adjusting screw

idling speed

if necessary

)

m

m

 

5

6

.

0

n

i

 

6

2

0

.

 :

P

A

G

t

s

u

j

d

a

e

r

 

d

n

a

 

n

a

e

l

c

spark plug

plug gap

replace, if necessary

intake air cooling vent

clean

throttle lever, ignition switch

check operation

replace if

drill

something’s wrong

gear box

oil

screws/nuts/bolts

tighten/replace

not adjusting screws

 

WARNING

Make sure that the engine has stopped and is 

cool before performing any service to the ma-

chine.  Contant with hot exhaust my cause injury.

Do not modify the drill or dismantle the engine.

When replacing parts use Kiam original parts.

AIR FILTER

(1) Filter element

If air filter blocked, will reduce engine performance.

Check filter element (1).  Clean in warm soapy water 

when required.  Dry completely before installing.  If 

filter is damaged or shrunk, replace with new one.

 

IMPORTANT

If the air filter is blocked, the efficiency of the engine 

will be reduced.  In addition, internal engine compo-

nents will suffer abnormal wear if operated with the 

filter or if continually operated with damaged filter.

FUEL FILTER

After

 eve

ry

 25 

hours

 

of

 

operation,

 

empty

 

the

 

fuel

 

tank,

detach

 

the

 

fuel

 

filter

 

from

 

the

 

tank,

 

and

 

remove

 

all

 

dirt.

 I

f

the

 

filter

 

is

 

too

 

clogged,

 

replace

 

with

 a 

new one.

(1) Fuel filter

Summary of Contents for Sherwood KA500















Reviews: