background image

 

5. For safe operation

6

 IF SOMEONE COMES

1. Guard against hazardous situa-

tions at all times. Warn adults to

keep pets and children away from

the area. Be careful if you are ap-

proached. Injury may result from

flying debris.

2. If someone calls out or otherwise

interrupts you while working, al-

ways be sure to turn off the en-

gine before turning around.

MAINTENANCE

1. In order to maintain your product

in proper working order, perform

the maintenance and checking

operations  described  in  the

manual at regular intervals.

2. Always be sure to turn off the en-

gine before performing any main-

tenance or checking procedures.

  WARNING

The metallic parts reach high tem-

peratures immediately after stop-

ping the engine.

3.

4. Do not use any accessory or at-

tachment other than those bear-

ing the Kiam mark and recom-

mended for the unit.

5. Under no circumstances should

you ever take apart the product

or alter it in any way. Doing so

might result in the product be-

coming damaged during opera-

tion or the product becoming un-

able to operate properly.

HANDLING FUEL

1.

2. Never smoke while operating the

unit or refilling its fuel tank.

3. When refilling the tank, always

turn off the engine and allow it to

cool down. Take a careful look

around to make sure that there are

no sparks or open flames any-

where nearby before refueling.

4. Wipe spilled fuel completely us-

ing a dry rag if any fuel spillage

occurs during refueling.

5. After refueling, screw the fuel cap

back tightly onto the fuel tank and

then carry the unit to a spot 3 m

or more away from where it was

refueled before turning on the en-

gine.

TRANSPORTATION

1. When hand-carrying the product,

cover over the drill if necessary,

lift up the product and carry it

paying attention to the drill.

2. Never transport the product over

rough roads over long distances

by vehicle without removing all

fuel from the fuel tank. If doing so,

fuel might leak from the tank dur-

ing transport.

In the event that any part must 

be replaced or any maintenance 

or  repair  work  not  described  in 

this manual must be performed, 

please contact your authorized 

Kiam dealer for assistance.

The engine of the product is 

designed to run on mixed fuel 

which contains highly flammable 

petrol.  Never store cans of fuel 

or refill the tank of the unit in any 

place  where  there  is  a  boiler, 

stove, wood fire, welding sparks, 

electrical sparks or any other 

source  of  heat  or  fire  which 

might ignite the fuel.

Summary of Contents for Sherwood KA500















Reviews: