background image

11

Symptom

Possible Cause

Solution

No Subwoofer Output

Fuse not installed in inline fuse 
holder on subwoofer and / or amp 
harness

Install fuse into fuse holder.  
Refer to instructions for correct 
placement

Low battery voltage

Recharge the battery

Negative battery cable not 
connected

Reconnect negative battery cable

Power wire connector not 
connected to body harness

Connect power wire to body 
harness.  Check for loose 
connection

Ground wire not grounded properly

Check ground wire with voltmeter 
to insure it is a good ground

Balance or fader controls not set to 
neutral position

Set balance and fader control to 
center settings. (only effects stand 
alone subwoofer kit)

No low frequency information in 
music

Test with several different songs

Subwoofer harness not properly 
/ completely connected to sub-
woofer.

Securely fasten both of the 
connectors on the subwoofer 
harness to the subwoofer. Check 
for loose connections.

Radio Not Coming On

Blown radio fuse

Refer to owner's manual for radio 
fuse location and value

Low battery voltage

Recharge the battery

Radio Comes On, But No 

Sound From Any Speakers

Fuse not installed in inline fuse 
holder on amplifi er harness

Install fuse into fuse holder.  Refer 
to instructions for correct place-
ment

Ground wire not grounded properly

Check ground wire with voltmeter 
to insure it is a good ground

Low battery voltage

Recharge the battery

stillwater

designs

P.O. Box 459 • Stillwater, Oklahoma 74076 • USA • (405) 624–8510

If you continue to experience problems after troubleshooting, please contact KICKER Technical Support at 
(800) 256-0808 ext. 6009, or 

support@kicker.com

.

Summary of Contents for PF150S11













Reviews: