Kikusui PWR1201H User Manual Download

Page: 9 / 147

PWR-01

Name

Function

POWER switch

Press the ( ) side to turn on and the ( ) side to turn off.

p.28, p.29

Voltmeter

Displays the voltage, alarm, or CONFIG parameter number.

p.34, p.54

OUTPUT LED

Lights green when output is turned on. Blinks orange during output-on delay. Blinks
green during output-off delay.

p.37

Blinks orange when output is on and a protection function is activated.

p.46

Lights green during soft start. Blinks green during soft stop.

p.39

Ammeter

Displays the current, power, or the cause of an alarm, or the value of a CONFIG param-
eter.

p.34, p.46,

p.54

OUTPUT key

Used to turn output on and off.

p.37

VIR/ SS/ DLY/ SEQ/ HB

VIR: Lights when the variable internal resistance function is enabled.
SS: Lights when the soft start/ stop function is enabled and blinks when it is in progress.
DLY: Lights when the output-on/ off delay is enabled and blinks when it is in progress.
SEQ: Lights when a sequence is being executed and blinks the PWR-01 is waiting for a
trigger.
HB: Lights when the hyper bleeder of the bleeder circuit is enabled.

p.78
p.39
p.38
p.79
p.76

PRESET A/ B/ C LED

A: Lights green when the memory A values are being recalled or saved.
B: Lights green when the memory B values are being recalled or saved.
C: Lights green when the memory C values are being recalled or saved.

p.70

SET key

Used to set and confirm the output voltage and output current (the key has an LED).

p.34

ALM CLR key

Used to release the activated state (alarm) of protection functions (the key has an LED).

p.46

OVP•OCP key

Used to set and display the overcurrent protection (OCP), overvoltage protection (OVP),
undervoltage limit (UVL) trip points (the key has an LED).

p.47, p.52

SC1

Used to call the CONFIG parameter shortcut (the key has an LED)

p.72

CONFIG key

Used to configure the various operating conditions (CONFIG) (the key has an LED).

p.54

SC2

Used to call the CONFIG parameter shortcut (the key has an LED)

p.72

VOLTAGE knob

Used to set the voltage value or select the value of a CONFIG parameter.

p.36, p.54

FINE

Used to make fine voltage value adjustments.

p.36

12 CV LED

Lights green during constant voltage mode.

p.45

13 CC LED

Lights red during constant current mode.

p.45

CURRENT knob

Used to set the current, change the value of a CONFIG parameter, or set the internal
resistance value.

p.36, p.54,

p.59

FINE

Used to make fine current or internal resistance value adjustments.

p.36, p.59

ALM LED

Lights red when a protection function is activated. However, when the undervoltage limit
(UVL) is activated, the LED does not light. When the power limit (POWER LIMIT) is acti-
vated, the LED blinks.

p.71

RMT LED

Lights green when the PWR-01 is being remotely controlled

p.73

LOCK LED

Lights green when the keys are locked.

p.71

LAN LED

Lights and blinks when the LAN interface is running.
• No fault status (green)
• Fault status (red)
• Standby status (orange)
• Identify status (blinking green)

Communica-

tion Interface

Manual

LOCAL key

Used to switch between local mode and remote mode (the key has an LED) and switch
the CONFIG parameter display.

p.73

SHIFT key

Used to enable the functions that are written in blue characters below the key.

–

PWR DSPL key

Used to display the output power on the ammeter (the key has an LED).

p.34