background image

Page 4 of 9 

Killion Industries, Inc. • 1380 Poinsettia Ave., Vista, CA  92081 

Phone (760) 727-5102 • Toll Free (800) 421-5352 • Fax (760) 727-1622 

www.killionindustries.com • Sales@killionindustries.com • Parts.Service@killionindustries.com 

 

 

Regular periodic cleaning will ensure proper operation, minimize maintenance costs, and prolong the life of 

refrigerated merchandisers.  The following maintenance should be performed every three months.  Depending 
on the conditions of your store, you may need to increase maintenance intervals. 

 

 
 
 
 

 
 
 

 

 

 

Routine Maintenance 

 

 

Clean all dust and debris from the merchandising display areas. 

 

Clean all air grills, grates, honeycombs, and panels with warm water and a mild detergent. 

 

Remove access panel(s) (lower side panel) screws to expose evaporator coil, drain pan, and 

condensate pump. 

 

Clean case interior and pull down shades with a damp rag soaked in mild soap and water.  Remove 

the shelving and display racks and clean with mild soap and water.  Wipe down light tubes and interior 

surfaces. 

 

Clean the dust from all air grills using mild soap and water. 

 

Vacuum interior bottom and wipe clean of sediment or deposits in coil drain pan and around 

condensate pump.  Wipe evaporator fan blades clean to remove any dirt or film that may be 
deposited on them.  Use caution to not bend blades with undue pressure. 

 

Clean evaporator coil with a non-acidic, EPA approved cleaner, such as Nu-Brite or Alka-Brite, or 

comparable product. 

 

Check the pumps and pump lines for blockage.  Be sure condensate pumps are operating and freely 

transferring condensate water. 

 

Replace access panels (screw into place). 

 

Vacuum the top of the case in the compressor area to remove dust and debris from the compartment. 

 

Check refrigerant level through sight glass (located near the condensing unit), if bubbles are visible, the 

unit is low on refrigerant.  (Call a qualified refrigeration service technician for service). 

ROUTINE MAINTENANCE 

Remove product to a suitable storage refrigerator while 

performing maintenance.  Turn off refrigerated merchandiser 

and disconnect from electrical source prior to performing 

maintenance. 

WARNING

Enlevez le produit sur un réfrigérateur approprié de stockage  

tout en exécutant l'entretien. Tournez le marchandiseur au  

loin frigorifié et le démontez de la source électrique avant  

d'exécuter l'entretien. 

 

AVERTISSEMENT

 

Summary of Contents for CFFM-93-57-99












Reviews: