background image

Page 6 of 9 

Killion Industries, Inc. • 1380 Poinsettia Ave., Vista, CA  92081 

Phone (760) 727-5102 • Toll Free (800) 421-5352 • Fax (760) 727-1622 

www.killionindustries.com • Sales@killionindustries.com • Parts.Service@killionindustries.com 

Stocking / Product Load Limits 

 

The cold air re-circulating system requires free airflow through all grills, including the grill above the bottom well 
at the front of the refrigerator.   

 

 

DO NOT place product in merchandisers until case is at proper operating temperature. 

 

DO NOT stock the product so tightly that the refrigerated airflow is hampered.  Overstocking 

refrigerated merchandisers can lead to reduced temperature holding capacity and expose the unit to 

undue strain. 

 

DO NOT stock product so tightly against back wall that airflow is restricted.  There should be at least a 

one-inch gap between the back of the case and product. 

 

DO NOT block any air grills, honeycomb air discharge areas, or any panels with slots intended for air 
intake or discharge. 

 

DO NOT dump excess product water into the case.  This will cause strain on the condensate removal 

systems that can cause the case or condensate systems to leak and overflow.  The fertilizer used in floral 
display water can also plug pumps and condensate lines leading to leaks and overflow. 

 

 

 

 
 

 

 
 
 

 
 

 
 
 
 

 

Relocating / Moving 

 

Before moving or relocating a case that has been in use, it is important to remove all condensate water from 
evaporator pans, so that water damage does not occur.  A wet/dry vacuum works well to remove water.   

 

Be sure that all plumbing and electrical connections are disconnected before attempting to relocate the case.  
Follow all directions in the 

Pre-Installation

 and 

Installation

 sections when placing the unit in its new location. 

Proper product rotation is necessary to prevent 

product loss.  Move older product to the front of the 

case and set the newer product in the back. 

 

CAUTION

 

La rotation appropriée de produit est nécessaire pour empêcher 

la perte de produit. Déplacez un produit plus ancien à l'avant du 

cas et placez le produit plus dans le dos. 

ATTENTION

 

Summary of Contents for CFFM-93-57-99












Reviews: