Kimberley Monaco Installation Instructions Manual Download

Page: 1 / 14

50 Years

KIMBERLEY

Established over

www.kimprod.com.au

‘Monaco’

60lt Dual Capacity

Recycling Solution

‘Side’ Mount

All measurements are in millimeters

Minimum Cupboard Dimension:

Side Mount:

550 (h) x 534 (d) x 414 (w) Maximum Width: 418

Min. 550

Min 414 Max 418

Min. 534

PARTS LIST

• Mounting Brackets

x 2

• Runner Brackets

x 2

• Frame Assembly

x 1

• Door Mounting Brackets

x 2

• Lid Assembly

x 1

• Buckets

x 2

ASSEMBLY KIT

• Screws (8g x 17mm

button head

) x 16

• Screws (M5 x 12mm

Roof

)

x 10

• Star Washers

x 4

TOOLS REQUIRED

• Phillips Head Screwdriver

• Drill & 2mm Drill Bit

Figure 1.

Use these Instructions for

‘SIDE’

Mount

Installations only.

All Illustrations are NOT to scale.

Installation Instructions

Please see the other end

of the Instructions for

‘TOP’

Mount

Installations.

D/N: SKRB60E-160817

Summary of Contents for Monaco















Search results

Summary of Contents for Monaco

Reviews:

Related manuals for Monaco

Brands by name

Popular brands

Kimberley Monaco, Installation Instructions Manual

Search results

Summary of Contents for Monaco

Reviews:

Related manuals for Monaco

Brands by name

Popular brands