Kimberly-Clark Suretouch Installation Instructions Manual Download

Page: 19 / 19

Americans with Disabilities Act (For use in U.S. only): Title III of the Americans with Disabilities Act (“ADA”)

governs, in detail, the placement and operation of dispensers. You should ensure that your mounting and

use of dispensers complies with that law as well as the regulations issued under that statute. The mounting

suggestions in this document may or may not fulfill the obligations of the ADA with respect to your facility.

Ley de protección de discapacitados (aplicable sólo en EE.UU.). El Artículo III de la Ley de protección de

discapacitados, ADA (

Americans with Disabilities Act) regula en detalle la instalación y el funcionamiento de

distribuidoras. Asegúrese que la instalación y las disposiciones de uso de la distribuidora cumplan con esta

ley y los reglamentos correspondientes derivados de ella. Es posible que las instrucciones de instalación aquí

descritas cumplan o no con las disposiciones de la ADA dependiendo de las características de su construcción.

Loi concernant les Américains handicapés : Le titre III de l’

Americans with Disabilities Act (« ADA ») (Loi

concernant les Américains handicapés) régit, de façon détaillée, l’emplacement et le fonctionnement des

boîtes distributrices. Vous devez veiller à ce que votre méthode de pose et d’utilisation des boîtes distributrices

soit conforme à la loi, de même qu’aux règlements y afférents. Les suggestions relatives à la pose qui figurent

dans le présent document peuvent répondre ou non aux exigences de l’ADA dépendant du type d’installation.

KIMBERLY-CLARK CORPORATION DISCLAIMS LIABILITY FOR PERSONAL INJURIES OR

PROPERTY DAMAGES RESULTING FROM INSTALLATION NOT PERFORMED BY KIMBERLY-

CLARK.
KIMBERLY-CLARK CORPORATION RECHAZA TODA RESPONSABILIDAD POR LESIONES

PERSONALES O DAÑOS Y PERJUICIOS DEBIDOS A INSTALACIONES NO REALIZADAS POR

KIMBERLY-CLARK.
KIMBERLY-CLARK CORPORATION DÉCLINE TOUTE RESPONSABILITÉ POUR LES BLESSURES

PERSONNELLES OU LES DOMMAGES À LA PROPRIÉTÉ RÉSULTANT D’UNE INSTALLATION

N’AYANT PAS ÉTÉ EFFECTUÉE PAR KIMBERLY-CLARK.
KIMBERLY-CLARK CORPORATION HAFTET NICHT FÜR DURCH EINE INSTALLATION

ENTSTANDENE PERSONEN- BZW. SACHSCHÄDEN, WENN DIESE VON ANDEREN ALS VON

KIMBERLY-CLARK DURCHGEFÜHRT WURDE.
KIMBERLY-CLARK CORPORATION AANVAARDT GEEN AANSPRAKELIJKHEID VOOR

LICHAMELIJK LETSEL OF MATERIËLE SCHADE DIE VOORTVLOEIT UIT EEN NIET DOOR

KIMBERLY-CLARK UITGEVOERDE INSTALLATIE.
KIMBERLY-CLARK CORPORATION ESCLUDE LA PROPRIA RESPONSABILITÀ PER DANNI ALLA

PERSONA O A PROPRIETÀ DERIVANTI DA OPERAZIONI DI INSTALLAZIONE NON EFFETTUATE

DA KIMBERLY-CLARK.
КОМПАНИЯ KIMBERLY-CLARK CORPORATION СНИМАЕТ С СЕБЯ ОТВЕТСТВЕННОСТЬ ЗА

ТЕЛЕСНЫЕ ПОВРЕЖДЕНИЯ ИЛИ УЩЕРБ ИМУЩЕСТВУ, ЯВЛЯЮЩИЕСЯ РЕЗУЛЬТАТОМ

УСТАНОВКИ, ВЫПОЛНЕННОЙ НЕ КОМПАНИЕЙ KIMBERLY-CLARK.
A KIMBERLY-CLARK CORPORATION DECLINA QUALQUER RESPONSABILIDADE POR LESÕES

PESSOAIS OU DANOS MATERIAIS RESULTANTES DE INSTALAÇÃO NÃO EFECTUADA PELA

KIMBERLY-CLARK.

®/* Trademarks of KimberlyClark Worldwide, Inc. / Marques déposées de KimberlyClark Worldwide, Inc.

Summary of Contents for Suretouch




















Search results

Summary of Contents for Suretouch

Reviews:

Related manuals for Suretouch

Brands by name

Popular brands

Kimberly-Clark Suretouch, Installation Instructions Manual

Search results

Summary of Contents for Suretouch

Reviews:

Related manuals for Suretouch

Brands by name

Popular brands