background image

INSTALLATION                                                                                                         

 

INSTALLING OR REMOVING BLADE 

 

WARNING: 

To reduce the risk of serious personal injury, turn unit off 

and remove the battery pack before making any adjustments or 
removing/installing attachments or accessories. An accidental 
start-up can cause injury. Different blade lengths are available. Use 
the appropriate blade for the application. The blade should extend 
past the shoe and the thickness of the workpiece during the cut. Do 
not use jigsaw blades with this tool. 

 

     

 
 
 

1. Reciprocating Saw Blade     
2. Blade Clamp Sleeve 

 
 

INSTALLATION 
A.

 Rotate the blade clamp sleeve. 

B.

 Insert the reciprocating saw blade into the blade clamp as far as it 

will go. 

C.

 Release the blade clamp sleeve and it will fixes the blade 

automatically. 

D.

 To remove blade, follow the installation procedure in reverse. 

 

WARNING: 

• 

Make sure that the blade cannot be extracted even though you 
try to pull it out. 

• 

If  you  do  not  insert  the  recipro  saw  blade  deep  enough,  the 
recipro saw blade may be ejected unexpectedly during operation. 
This can be extremely dangerous. 

 

Summary of Contents for 23802















Reviews: