30
Gently insert the narrow backrest board (14) into the sockets located beneath the backrest at
the legs from inside. Insert the vertically rectangular nut (from the right side/ leg 1) (15) to the
already inserted narrow board. Insert the bolt (9) into the orifice in the leg and then tighten
through the board into the nut (figure VII). Pay attention that the bolt must match the nut.
Repeat this step at another side of the narrow board, however remember not to tighten the
bolt to leave play for assembly of other elements. The figure VIII shows the assembled elements.
Place the bow-shaped handle with safety belts (8) in the sockets at the legs from inside. Then
fix the small board (6) at the highest position and the large board (7) at the position 3/4/5
(figures IX and IXa). Tighten firmly all bolts in the chair. Insert belts into the narrow orifices in
the small board (6) and the narrow backrest board (14). After sliding the belt through the orifice
straighten the stitching in the way arranging the belt and the stitching perpendicularly to each
other (figure XIII). Make sure the belts are not twisted at any point (figure XII).
Then attach the fitting (17) to the two remaining orifices located at the legs from outside.
Tighten the fitting to the chair with the bolts (18) using the Allen wrench (12) (figure X).
After pressing side red buttons insert the tray (16) into the fittings (figure XI). The tray is
mounted correctly, if, after being removed, you will hear the characteristic sound of the buttons
going forward.
After reassuring yourself all elements are mounted within the structure and there is nothing
left, firmly tighten all bolts in the chair.
Cushion assembly*:
You will find two cushions in the set. The cushion with a hole is intended for the seat (19), while
the second cushion is intended for the backrest (20). To attach the cushion to the seat, slide the
crotch strap through the hole in the cushion, disconnect the straps on the cushion and then slide
it through the chair. Reconnect the belts under the seat with Velcro straps. To attach the cushion
to the backrest, disconnect the straps on the cushion and then slide them through the chair
element. Reconnect the straps with Velcro (Figure XIV*).
E. Belt adjustment
The belts are adjusted by means of plastic clamps. Adjust belt length to baby’s size. Attention!
The belts protect a baby against falling from the chair, must stabilize baby position, however
they must not be too tight and uncomfortable.
F. Assembly of the chair for older children:
You will need the Allen wrench (12). Perform assembly on soft surface that will not damage
surface of elements.
Start from assembling the leg (1) with the cross-bar (4). Notice that there are protruding pins in
the cross-bar. Gently adjust the protruding element with the first orifice from the bottom. Look
at the figure I and adjust the cross-bar in the way enabling you to insert the cylinder nut (11)
Summary of Contents for ENOCK
