background image

Technical Specifications 

Model ......................................................................................................KC-1502LED-C 
Voltage/Capacity ....................................................................................7.4V, 2,600 mAh 
Battery type ....................................................................................................Lithium-ion 
Lumens ......................................................................................................1,500 (6500K) 
Wattage ....................................................................................................................10W 
Charger ....................................................................................................................120V 
Charge time/Runtimes ..........................................................................................3 hours 
LED life ......................................................................................................+30,000 hours 

 
WARNING

: The warnings, cautions, and instructions discussed in this instruction manual 

cannot cover all possible conditions and situations that may occur. It must be understood 
by the operator that common sense and caution are factors which cannot be built into this 
product, but must be supplied by the operator. 
 

WARNING: 

Get to know your LED work light. Do not use until you have read and    

understood this instruction manual. Only use the supplied King charger to charge the 7.4V 
Lithium-ion batterie.  
 

Battery and Charger Safety Precautions 

 

1) Never attempt to open the battery

 for any reason. If battery housing has cracked,    

discontinue use immediately and do not try to recharge it.  

2) Never charge a wet LED work light

 or if battery shows signs of corrosion. 

3) Do not use an extension cord

 with the charger, plug charger directly into a 120V AC 

receptacle. 

4) Do not use charger

 if power its cord is damaged, replace damaged cord or charger. 

5) Do not charge battery

 when work area or the temperature is or below 0

0

C or above 

45

0

C. 

6) Unplug charger

 when not in use. 

7) The contents of the battery is slightly acidic

, do not incinerate the battery, it can 

explode in a fire. 

8) A small leakage from the battery

 may occur under extreme usage, charging or     

temperature conditions. This does not indicate a battery failure. However, if the battery 
housing is cracked and leakage gets on your skin, follow these steps; 
-Wash with soap immediately. 
-Neutralize area with mild acid such as vinegar or lemon juice. 
-If leakage gets into your eyes, flush with clean water for a minimum of 10 minutes, then 
seek medical attention.

 

 

Lithium-ion Battery 

 
Lithium-ion batteries do not have a memory and do not require to be completely    
discharged periodically. After use, charge battery so that it is fully charged for the next time 
you use this tool. A fully charged battery will only loose about 2% of its charge per month 
during storage. 
 

LITHIUM BATTERY AND CHARGING  

INFORMATION

Summary of Contents for KC-1502LED-C








Reviews: