background image

wARRANTY & SERvICE

INFORMATION

1-YEAR 

LIMITED wARRANTY 

FOR 20 TON 6.5 hP GAS LOG SLITTER 

KING CANADA TOOLS

OFFERS A 1-YEAR LIMITED wARRANTY 

FOR NON-COMMERCIAL USE.

BEFORE  CALLING  ThE  ABOvE  TOLL-FREE  NUMBER,  PLEASE  READ  ThIS  MANUAL,  SPECIFICALLY  ThE

SAFETY PRECAUTIONS, ThE INSPECTION BEFORE OPERATION AND ThE TROUBLEShOOTING GUIDE.

• DO NOT RETURN ThE DEFECTIvE PRODUCT TO ThE RETAILER.

wARRANTY INFORMATION

PROOF OF PURChASE

Please keep your dated proof of purchase for warranty and servicing purposes.

REPLACEMENT PARTS

Replacement parts for this log splitter are available through our authorized KING CANADA generator service centers across canada.

For servicing, call the above toll free number to get servicing instructions and be sure to have your proof of purchase if you are claiming

warranty work.

LIMITED TOOL wARRANTY

KING CANADA makes every effort to ensure that this product meets high quality and durability standards. KING CANADA warrants to

the original retail consumer a 1-year limited warranty as of the date the product was purchased at retail and that each product is free

from defects in materials. 

ThIS wARRANTY IS NOT TRANSFERABLE AND DOES NOT COvER

• Damage or liability caused by shipping, improper handling, improper installation, improper maintenance, improper modification, or the 

use of accessories and/or attachments not specifically recommended.

• Repairs necessary because of operator abuse or negligence, or the failure to install, operate, maintain, and store

the product according to the instructions in the owner’s manual.

• Damage caused by cold, heat, rain, excessive humidity, corrosive environments and materials, or other contaminants.

• Expendable items that become worn during normal use such as fuel filters, air cleaners, spark plugs, engine oil or hydraulic oil.

• Cosmetic defects that do not interfere with product functionality.

• Freight costs from customer to an authorized warranty service location.

• Repair and transportation costs of products or parts determined not to be defective.

• ANY INCIDENTAL, INDIRECT OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM ANY DEFECT, 

FAILURE OR MALFUNCTION OF THE PRODUCT.

• RETAIN ThE ORIGINAL CASh REGISTER SALES RECEIPT AS PROOF OF PURChASE FOR wARRANTY wORK.

KING CANADA shall in no event be liable for death, injuries to persons or property or for incidental, special or consequential damages

arising from the use of our products. Shipping and handling charges may apply. If a defect is found, KING CANADA will either repair or

replace the product.

PARTS DIAGRAM & PARTS LISTS

Refer to the Parts section of the King Canada web site for the most updated parts diagram and parts list.

KING CANADA TOOLS INC. DORvAL, qUEBEC, CANADA h9P 2Y4

Summary of Contents for Power Force KCG-20LS















Reviews: