background image

FAULT FINDING GUIDE

PROBLEM

CHECK

NOTHING WORKS

Is the oven switched on at the socket ?
Is the fan oven switch on?
Is trip on main fuse board on ?
Has fuse blown in plug ?
*If trip/fuse continues to trip/blow after 
resetting/replacing; consult service engineer
*Top oven bulb may not be working
- giving the 

impression

that the oven is not working!

If all above are OK but oven still does not heat up

-

see 

below

OVEN NOT HEATING UP   Turn oven thermostat knob to mid setting (150 - 200ºC) 

in line with neon: does neon light up ?

Yes 

- look inside oven to see if fan blade is turning (F 

models only)

No and fan not turning

- consult service engineer

OVEN BURNING PRODUCT    Is thermostat turned 

above

220 ºC (temperature in 

line with neon)?

Yes

- try a lower setting (180 - 200 ºC)

*Larger potatoes may need cooking at lower 

temperature for longer to prevent over cooking 
outside before inside is cooked

No

- does neon light go off when temperature knob is 

turned to low setting (below 100 ºC) or off ?                     

No

- consult service engineer

THERMAL CUT-OUT

The whole oven, (lights, elements and fan) cycles off   
and  then on again some time later indicating a 
replacement thermostat is required.

Yes

- consult service engineer

Summary of Contents for CLASSIC 50









Reviews: