EN
PROGRAMMING THE TIMER FUNCTION
1.
Select the channel of the receiver to be programmes and hold
pressed the P1 button: the LED corresponding to the selected
channel will turn on for a few seconds
2.
When the led goes off, release the P1 button.
3.
The led starts a sequence of flashings at low speed (1 flash
per second). The number of flashing corresponds to the time
which can be set as shown in the table.:
N° Flashing
Time
N° Flashing
Time
1
01 sec.
17
1 min.
2
02 sec.
18
1,5 min.
3
03 sec.
19
2 min.
4
04 sec.
20
2,5 min.
5
05 sec.
21
3 min.
6
06 sec.
22
3,5 min.
7
07 sec.
23
4 min.
8
08 sec.
24
4,5 min.
9
09 sec.
25
5 min.
10
10 sec.
26
5,5 min.
11
11 sec.
27
6 min.
12
12 sec.
28
6,5 min.
13
13 sec.
29
7 min.
14
14 sec.
30
7,5 min.
15
15 sec.
31
BISTABLE
16
30 sec.
4.
Count the number of led flashings corresponding to the time
you wish to set
5.
Press the rx button P1 during the wished flashing: the
sequence of flashings stops and the led remains on
6.
Within 5 seconds, press and hold the button on the remote
control (about 2 sec.)
7.
The led on the receiver is turned off and then comes on
again: the code has been memorised and the receiver remains
standby for 5 s with a new code to be memorised
8.
Memorise all the remote control units necessary
9.
After 5 seconds without a valid transmission, the led is turned
off and the receiver returns to normal operating mode
PROGRAMMING OF THE BISTABLE
FUNCTION
1.
Select the channel of the receiver to be programmes and hold
pressed the P1 button: the LED corresponding to the selected
channel will turn on for a few seconds
2.
When the led goes off, release the P1 button.
3.
The led starts a sequence of flashings at low speed (1 flash per
second). When the 30 flashings of the timer function are over,
the led remains on.
4.
Within 5 seconds, press and hold the button on the remote
control (about 2 sec.)
5.
The led on the receiver is turned off and then comes on
again: the code has been memorised and the receiver remains
standby for 5 s with a new code to be memorised
7.
Memorise all the remote control units necessary
8.
After 5 seconds without a valid transmission, the led is turned
off and the receiver returns to normal operating mode
REMOTE RADIO LEARNING
This procedure allows to memorize new transmitters by radio, in
sequence and without removing the receiver from the installation.
The transmitter which allows to enable the programming
by radio must be memorized in advance.
The keys of all the transmitters saved in the memory via radio will
have the same logic as for those of the transmitter that enabled
programming.
Therefore, if the transmitter that activated programming has key 1
saved only, the new transmitters can only be saved using key 1.
1.
Press for at least 4 seconds the keys 1+2 of one transmitter
that is already saved
2.
Release both keys
3.
Press, within 5 seconds, the key of the new transmitter that
you intend to save
4.
Release the key and repeat the procedure for the other keys of
the remote control or with other radio controls to be saved
CANCELLATION OF A SINGLE
TRANSMITTER
1.
Turn off the power to the receiver
2.
Holding down the P1 key, reactivate the power supply: LED L1
lights up steadily for a few seconds then starts flashing
3.
During flashing, release the P1 key: LED L1 turns on steadily
4.
Hold down a key of the transmitter that you want to delete:
LED L1 turns off and on again
5.
Release the key: the transmitter has been deleted (all keys
memorized) and the receiver remains on hold for 5 sec. of
another transmitter to be deleted
6.
After 5 seconds without any operation, the LED turns off and
the receiver returns to normal operation
NOTE: if you try to delete a transmitter that is not
memorized, the L1 LED flashes multiple times
TOTAL CANCELLATION OF
TRANSMITTERS
1.
Turn off the power to the receiver.
2.
Holding down the P1 key, reactivate the power supply: LED L1
lights up steadily for a few seconds then starts flashing
3.
Keep the button pressed until LED L1 remains on steady
4.
Release the P1 key: the total cancellation is started and ends
after a few seconds when the LED goes out
Manufacturer's details
Brand of V2 S.p.A.
Corso Principi di Piemonte 65/67 - 12035 RACCONIGI CN (ITALY)
info@king-gates.com - www.king-gates.com
