background image

WARRANTY INFORMATION

2-YEAR  

LIMITED WARRANTY  

FOR THIS BELT AND DISC SANDER 

KING CANADA TOOLS 

OFFERS A 2-YEAR LIMITED WARRANTY  

FOR NON-COMMERCIAL USE.

PROOF OF PURCHASE 

 

Please keep your dated proof of purchase for warranty and servicing purposes. 

 

PARTS DIAGRAM & PARTS LISTS 

 

Refer to the Parts section of the King Canada web site for the most updated parts diagram and parts list. 
 

LIMITED TOOL WARRANTY 

 

King Canada makes every effort to ensure that this product meets high quality and durability standards. King Canada warrants to the 
original retail consumer a 2-year limited warranty as of the date the product was purchased at retail and that each product is free from 
defects in materials. Warranty does not apply to defects due directly or indirectly to misuse, abuse, normal wear and tear, negligence 
or accidents, repairs done by an unauthorized service center, alterations and lack of maintenance. King Canada shall in no event be 
liable for death, injuries to persons or property or for incidental, special or consequential damages arising from the use of our products.  
 
To take advantage of this limited warranty, return the product at your expense together with your dated proof of purshase to an                 
authorized King Canada service center. Contact your retailer or visit our web site at www.kingcanada.com for an updated listing of our 
authorized service centers. In cooperation with our authorized serviced center, King Canada will either repair or replace the product if 
any part or parts covered under this warranty which examination proves to be defective in workmanship or material during the              
warranty period. 
 

NOTE TO USER

 

 
This instruction manual is meant to serve as a guide only. Specifications and references are subject to change without prior notice. 
 
 

 
 

 
 
 
 
 
 
 
 
 
 
 

KING CANADA INC. DORVAL, QUÉBEC, CANADA H9P 2Y4 

 

www.kingcanada.com

Summary of Contents for KC-790FX














Reviews: