Vehicle Starting and Driving
S-25
Engine start up and shut down
Procedures for engine start up
Don’t release parking brake and keep to place the gear box lever in neutral. The vehicle is not possible to
move in the gear position.
Turn the ignition key into “start” position.
Start up without stepping on the accelerator. If the engine does not work after about 20 seconds, interrupt
the start up process and wait at least 15 seconds before activating start again. To repeat start up, it is
necessary to turn the key back to the off position.
Let the ignition key loose as soon as the engine starts running.
The motor rotation adjusts itself automatically in function of the coolant temperature.
Indication:
The start up process is automatically interrupted after 90 seconds of continuous activation. In this case, in
order to repeat the start up activation, turn the ignition key back to the off position and wait at least 2
minutes.
After engine start up, the vehicle can be put immediately into operation.
Note
：
a. The engine should be running at low middle speed for 3-5 minutes on every day's first starting before the
driving.
b.
Never race the engine without warming up. During cold start, increase engine speed slowly and do not
make engine run at maximum speed until water temperature of engine reaches to 70°C. At any time, do not
make engine run at high speed under no load.
c.
Never make engine run at idle speed for more than 10 minutes.
d.
The oil pressure should be displayed on the dashboard in 15 seconds after the engine is started, otherwise,
stop engine to check..
e.
If parking brake indicator lights, indicating that parking brake has not be released.
Attention!
If on starting up the engine, the engine oil pressure indicator continues indicating low pressure, this means
that the engine running order is in danger. Immediately shut down engine, find and correct the failure.
Summary of Contents for XMQ6127 series
