background image

                                                                           

 

 

7

Appendix Toxic or Hazardous Materials or Elements  

Toxic or Hazardous Materials or Elements 

Component 

Name 

Pb 

Hg 

Cd 

Cr VI 

PBB 

PBDE 

Circuit Board 

Component 

 

 

 

 

 

 

Device 

Construction 

Material 

 

 

 

 

 

 

 

 

Wire and Cable 

 

 

 

 

 

 

 

 

Packing 

Components 

 

 

 

 

 

 

Accessories 

 

 

 

 

 

 

 

O: Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts 
is below the relevant threshold of the SJ/T11363-2006 standard. 
 
X: Indicates that the concentration of the hazardous substance of at least one of all homogeneous 
materials in the parts is above the relevant threshold of the SJ/T11363-2006 standard. During the 
environmental-friendly use period (EFUP) period, the toxic or hazardous substance or elements contained 
in products will not leak or mutate so that the use of these (substances or elements) will not result in any 
severe environmental pollution, any bodily injury or damage to any assets. The consumer is not authorized 
to process such kind of substances or elements, please return to the corresponding local authorities to 
process according to your local government statutes. 

 

Note

 

 

This manual is for reference only. Slight difference may be found in the user interface. 

 

All the designs and software here are subject to change without prior written notice.  

 

All trademarks and registered trademarks mentioned are the properties of their respective 

owners. 

 

If there is any uncertainty or controversy, please refer to the final explanation of us. 

 

Please visit our website or contact your local service engineer for more information. 

 

Summary of Contents for CVIOD-EL1MPIR50-E













Reviews: