background image

10

Step 1: Preparing the Pool

1.

Make sure the pool has adequate 
circulation. The total volume of pool 
water must completely circulate 
through the pump and fi lter at least 
1 to 2 times per day. This usually 
requires 8 to 12 hours of circulation. 
Check with your dealer for the 
proper circulation time for your pool.

2.

3.

5.

4.

Water Balance Guidelines

pH: 

7.2 – 7.8

Total Alkalinity:                

80 – 120 ppm

Calcium Hardness:           

200 – 400

Total Dissolved Solids:   

<1500

Stabilizer:                        

20 – 80 ppm

Free Chlorine: 

0.5 – 1.0 ppm

Check the pool’s fi lter gauge often 
and periodically clean fi lter per 
the manufacturer’s directions. 
A dirty fi lter will slow the fl ow of 
water which could hamper proper 
circulation.

Check the Water Hardness of your fi ll water before 
adding to the pool. If calcium content is higher than 
400 ppm, fi nd a soft water source to fi ll your pool 
instead; otherwise water balance will be very diffi cult.

Check for metals in the pool such 
as iron or copper. Before attempting 
water balance these should be 
removed. See your dealer for a metal 
out or sequesterant and follow the 
label directions carefully.

Before beginning with any pool care program, you 
must fi rst balance your pool water. Take a water 
sample to your local pool professional (or use a 
complete test kit) to test for the important Water 
Balance Guidelines. 

IMPORTANT:

 Always follow printed instructions on 

the balancing chemical packages. Add balancing 
chemicals in small increments, one at a time, 
with circulation running. 

For best results, wait 

8-12 hours

 before testing again and adding any 

additional balancing chemicals. 

Metal 

Out

WARNING

Do not exceed maximum operating 
pressure of 50 psi.

Summary of Contents for Pool Frog 6100

























Reviews: