2
3.
SAFETY FEATURES
1.
To avoid any short-circuit and to protect the clamps, which have a positive (=red) and negative (=black) current,
clamps must always be stored in the specially designed holders when not in use.
2.
The cable holders on the Jump Starter housing are to store the cables.
3.
Thanks to its 12V sealed, non-spillable lead acid battery, the Jump Starter may be used and stored in any position and
is state of the art technology.
4.
If you have a 12/24V unit, make always sure that the voltage selector switch is on “OFF” or that the voltage
connector plug is unplugged (depending on model) during transport or when not in use. It is normal that gage and
LED will not function in OFF position.
For charging: put the voltage selector switch in 12V position, or plug the
voltage connector plug in the 12V socket.
5.
Always attach the clamps correct to the terminals of the vehicle battery. Do not crank starter, without an installed
proper vehicle battery. Otherwise possible damage can occur to the electrical system of the vehicle or to the Jump
Starter!
6.
Some models are equipped with a buzzer and a warning light: For these models, the following steps
MUST
be
followed:
a-
12V or 24VModel: ON/OFF selector
MUST
be on “
OFF
” (clamps are Voltage free)
b-
12/24V Model: Voltage selector Switch
MUST
be on “
OFF
” or the voltage connector plug
MUST
be unplugged
(depending on the model), (clamps are Voltage free)
c-
Connect the clamps to the battery poles, when you hear the Buzzer or notice that a red warning light is burning,
Disconnect the clamps immediately and reconnect the clamps on the correct battery poles
!
d-
Warning:
Whenever the clamps on the Jump Starter are
NOT Voltage free
and are inversed connected to the
vehicle’s battery, the fuse will blow and buzzer can be damaged.
4.
CHARGE LEVEL
Version with control lights (LEDs) 12V, 12/24 and 24V
:
1.
Check power level of the Jump Starter by pressing the test button for 5 seconds, if you have a 12/24V unit first plug
the voltage connector plug in the suitable socket, or switch to the correct voltage if your models has a voltage
selector, (if it is unplugged or on the position OFF the LEDs will not light up). When 4 LEDs come on (2 red, 1
orange and 1green) your Jump Starter is ready for use. When 3 LEDs or less come on, the Jump Starter needs to be
recharged immediately according to the directions mentioned in the section 5.
2.
Press test button for 5 seconds. If all 5 LEDs stay on, your Jump Starter is fully charged.
3.
The fifth LED indicates that the battery is being charged and is also an alternator output test
. It will turn OFF
automatically when charger is disconnected.
Version with digital or analogic display 12V, 12/24V and 24V:
1.
Check power level of the Jump Starter by pressing the test button for 5 seconds, if you have a 12/24V unit choose the
suitable voltage with the voltage selector switch. If the voltage is lower than 12,4V (or 24.8V), the Jump Starter
needs to be recharged immediately according to the directions mentioned in the section 5.
2.
Check power level of the Jump Starter by pressing the test button for 5 seconds. If the voltage is between 12.4 and
13.3V (or Hi) or between 24.8 and 26.6V (or Hi), the Jump Starter is ready for use.
5.
WAYS TO RECHARGE THE JUMP STARTER
1.
With the supplied automatic charger, plugged in an 110V outlet (other voltages also available depending on your
model, please check with your distributor). If you use a 12/24V unit, put the voltage selector switch in 12V position
or plug the voltage connector in the 12V socket (depending on model) for charging. Caution, do not choose the 24V
position while charging. Check that the charger 12V-4A or 24V-2A is on by pressing the on/off button on the right.
2.
While driving by using the supplied charging cable connected to the cigar lighter socket of the vehicle. (The vehicle
should be started before plugging the cable in the cigar lighter socket). Charging will take 4 to 5 hours.
Summary of Contents for Mighty Seven FA-1214
Page 7: ...6 Notes ...
