background image

www.kingfisherboats.com 

27 

KINGFISHERBOATS.COM

 

27

 

 

 

Exclusions and implied warranties

 

Except as otherwise stated herein, KingFisher disclaims liability for any 

express or implied warranties, including any implied warranties of 

merchantability or fitness for a particular purpose. The factory disclaims 

liability for indirect, incidental or consequential damages, which disclaimer 

applies during and after the warranty period. This warranty is limited to an 

amount not exceeding the cost of correcting the defects as herein provided 

and shall not exceed the original retail purchase price paid for the product 

manufactured by KingFisher. At the expiration of the applicable warranty 

period all such liability shall terminate. This warranty does not extend to any 

engine or component installation which requires additional make ready 

servicing, adjustment or final assembly in preparation by the dealer for the 

delivery to the original purchaser, any defect due to the negligence of others; 

failure to operate or maintain the product in accordance with acceptable 

practices; unreasonable use; damage, accidents, abuse, damage resulting 

from impact, negligence, alterations, ordinary wear and tear; use of the 

product for racing purposes; use of performance products (other than those 

recommended by the factory) that place undue stress on parts such as "jack 

plates"; modifications of any sort; exceeding horsepower rating and load 

capacities as indicated on capacity plates fixed to the boat; de-rigging 

charges, failure to trim boat properly while running, trailering damage, towing 

behind another boat and other cases of misuse without limit. 

 

Company Policy 

No employee or representative is authorized to change this warranty in any 

way or grant any other warranty. 

 

This warranty gives you specific legal rights, and you may also have other 

rights, which vary from jurisdiction to jurisdiction. 

 

Design changes 

The factory reserves the right to make changes in the design or material of 

the product without incurring any obligation to incorporate such changes in 

any product previously manufactured, advertised, or sold. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for COASTAL Series




































Reviews: