background image

 

36   

 

Solar System Installation Guide 

Warranty 

Kingspan Solar Inc 

Warranty Statement for Solar and Electronic Goods 

 

Subject to the following provisions, Kingspan Solar Inc warrants that the Goods will be free from defects in material and workmanship for 

a period of 10 years in relation to THERMOMAX SOLAR PRODUCTS and a period of 2 years in relation to THERMOMAX ELECTRONIC 

PRODUCTS from their delivery to the Buyer. The warranty is given by Kingspan Solar Inc subject to the following conditions: 

 

A. Kingspan Solar Inc shall be under no liability in respect of any defect in the Goods arising from any information drawing design or 

specification supplied by the Buyer. 

B. Kingspan Solar Inc shall be under no liability in respect of any defect arising from fair wear and tear, willful or accidental damage, 

negligence, abnormal working conditions, failure to follow the Kingspan Solar Inc' instructions, misuse or alteration or repair of the 

Goods without approval. 

C. The above warranty does not extend to parts materials equipment not manufactured by Kingspan Solar Inc in respect of which the 

Buyer shall only be entitled to the benefit of any such warranty or guarantee as is given by the manufacturer to the Company. 

D. The defect has been reported by the Buyer to Kingspan Solar Inc within the warranty period. 

E. The installation of the Goods having been carried out by fully trained and competent person(s) authorized by Kingspan Solar Inc 

F. The Goods having been subjected to neither “prolonged stagnation conditions” nor exhibiting signs of “extreme temperature 

exposure”. 

 

1. The Buyer shall not make any statement or representation or give any warranty to any third party in respect of any Goods other than in 

the terms made or given by Kingspan Solar Inc to the Buyer nor shall the Buyer have any authority to commit Kingspan Solar Inc to 

provide any service in relation to the Goods. 

2. If Kingspan Solar Inc fails to deliver the Goods for any reason other than any cause beyond the Company's reasonable control or the 

Buyer's fault then Kingspan Solar Inc shall only be liable to the Buyer for and the Company's liability shall be limited to the excess (if any) 

of the cost to the Buyer (in the cheapest available market) of similar goods to replace those not delivered over the Price of the Goods. 

3. The Buyer shall examine all delivered Goods forthwith. Any claim based on any defect in the quality or condition of the 

Goods or their failure to correspond with specification shall be notified to Kingspan Solar Inc within 7 days from the  delivery date or 

where the defect was not apparent on reasonable inspection within a reasonable time after discovery of the failure. If delivery is not 

refused and the Buyer does not notify Kingspan Solar Inc the Buyer shall not be entitled to reject the Goods. 

4. Kingspan Solar Inc shall be entitled to examine any Goods, which are the subject of any claim by the Buyer, and to remove such Goods 

or any part thereof for testing. No tests carried out by the Buyer will be recognized by Kingspan 

Solar Inc unless carried out strictly in accordance with a method previously agreed by Kingspan Solar Inc as being suitable for the 

purpose. 

5. Any valid claim in respect of the Goods which is based on any defect in the quality or condition of the Goods or their failure to meet 

specification is notified to Kingspan Solar Inc in accordance with these Conditions. Kingspan Solar Inc shall be entitled to repair or 

replace the Goods (or the part in question) free of charge or at the Company's sole discretion refund to the Buyer the Price (or a 

proportionate part of the Price) but Kingspan Solar Inc shall have no further liability to the Buyer. 

6. Kingspan Solar Inc shall not be liable to the Buyer by reason of any representation (unless fraudulent) or any implied warranty 

condition or other term or any duty at common law (including but without limitation the negligence of Kingspan 

Solar Inc its employees agents or otherwise) or under the express terms of the Contract for any loss of production loss of profits or 

anticipated profits loss of contracts operation time or anticipated savings loss of business or of expected further business loss of or 

corruption to data damage to the Buyer’s reputation or goodwill damages costs or expenses payable by the Buyer to any third party or any 

other indirect special or consequential loss or damage or claim (whether caused by the negligence of Kingspan Solar Inc its employees 

agents or otherwise) which arise out of or in connection with the supply of the Goods or their use or resale by the Buyer. 

7. Without prejudice to the provisions of clauses 3, 4, 5, 6 and 7 the entire liability of the Buyer under or in connection with the Contract 

shall not exceed the Price of the Goods. 

8. Kingspan Solar Inc shall not be liable to the Buyer or be deemed to be in breach of the contract by reason of any delay in performing or 

any failure to perform any of the Company's obligations in relation to the Goods if the delay or failure was due to any cause beyond the 

Company's reasonable control.  

9. To obtain warranty coverage, the Buyer should contact the authorized contractor from whom the system was purchased or contact 

Kingspan Solar Inc. via  .kingspansolar.com, at 7510 Montevideo Road, Jessup MD 20794 or 1-800-231-7788. 

 

 

Summary of Contents for Thermomax HP Series






































Reviews: