background image

Varisol Installation Manual

19

18

Servicing and Maintenance

Users should regularly check the temperatures which the solar control panel is recording. 

With the SC range of controllers, simply pressing the ‘SET’ button on the fascia once will 

display the upper and lower collector temperatures since the control panel was last reset. If 

the collector temperatures have been excessively high i.e. over 170

˚

C, it is recommended that 

the antifreeze level checked using a refractometer by a qualified engineer.
A sample of the Tyfocor® LS antifreeze fluid can be extracted from the pump station at 

the pump itself. The large centre of the pump hub can be opened with a large flathead 

screwdriver. This should be opened slowly until a few drops of the antifreeze fluid are 

released. A sample of the fluid placed on the glass of the refractometer will display the level of 

antifreeze in the system. If the antifreeze has lost its antifreeze properties the system should 

be refilled with fresh Tyfocor® LS.
It is recommended that the solar system is serviced annually by a qualified engineer and 

immediately if the system shows evidence of having lost pressure or has discharged liquid

at the pressure relief valve. The Tyfocor® LS antifreeze fluid should always be replaced after 

7 years.

Maintenance schedule

A qualified person should service the system at the recommended intervals, using the 

maintenance schedule below. In addition the user should check the system pressure at 

regular intervals. A visual inspection of the pressure gauge is required to check that the 

system pressure is maintained at the level noted below.
The service engineer should complete the following; the shaded boxes should be completed 

if the system requires refilling:

 

Upon 

Year 1 

Year 2 

Year 3 

Year 4 

Year 5 

Year 6 

Year 7

 

commissioning

Date of inspection 

   

 

 

 

 

 

Expansion vessel

setting before filling 

   

 

 

 

 

 

System pressure 

   

 

 

 

 

 

Expansion vessel

setting after filling 

   

 

 

 

 

 

Flow rate 

   

 

 

 

 

 

Antifreeze level 

 

pH reading 

   

 

Inspection of barium

getter on tubes 

   

 

 

 

 

 

 

   

 

 

 

 

 

Engineer details 

   

 

 

 

 

 

Print name

 

   

 

 

 

 

 

Sign

 

   

 

 

 

 

 

Telephone No.

 

 

 

 

 

 

 

 

Summary of Contents for Varisol

























Reviews: