background image

ii

Kingston Technology Company

DE90i-S, Rev. A00

Limited Warranty

KINGSTON TECHNOLOGY COMPANY (“Kingston”) warrants that this product is free from defects in material
and workmanship. Subject to the conditions and limitations set forth below, Kingston will, at its option, either repair
or replace any part of this product which proves defective by reason of improper workmanship or materials. Repair
parts or replacement products will be provided by Kingston on an exchange basis, and will be either new or
refurbished to be functionally equivalent to new.

This warranty does not cover any damage to this product which results from accident, abuse, misuse, natural or
personal disaster, or any unauthorized disassembly, repair or modification.

Duration of Warranty

Lifetime Warranty:

 The following Kingston products are covered by this warranty for life: solid state memory (e.g.,

memory modules and boards), networking adapters and. hubs (excluding power supply unit), solid state PCMCIA
interface adapters, and microprocessor upgrade products.

Seven Year Warranty:

 The following Kingston products are covered by this warranty for a period of seven years

from the date of original retail purchase: storage enclosures, including power supply units, cables, terminators,
and accessories.

Five Year Warranty:

 The following Kingston products are covered by this warranty for a period of five years from

the date of original retail purchase: networking hub power supply unit; and all other Kingston products (other than
those products covered by a two-year or one-year warranty, as provided below).

Two Year Warranty:

 The following Kingston products are covered by this warranty for a period of two years from

the date of original retail purchase: Winchester hard disk drives in a 2.5 inch, 3.5 inch or 5.25 inch form factor.

One Year Warranty:

 The following Kingston products are covered by this warranty for a period of one year from

the date of original retail purchase: Winchester hard disk drives in a 1.8 inch form factor, optical reading and
storage products, and magnetic tape storage products.

Warranty Claim Requirements

To obtain warranty service, return the defective product, freight prepaid and insured, to your local authorized
Kingston dealer or distributor, or to the Kingston factory service center located at 17600 Newhope Street, Fountain
Valley, California 92708, U.S.A. You must include the product serial number (if applicable) and a detailed
description of the problem you are experiencing. You must also include proof of the date of original retail purchase
as evidence that the product is within the applicable warranty period. If you return the product directly to the
Kingston factory, you must first obtain a Return Material Authorization (“RMA”) number by calling Kingston
Customer Service at (714) 438-1810, and include the RMA number prominently displayed on the outside of your
package. Products must be properly packaged to prevent damage in transit.

Free Technical Support

Kingston provides free technical support. If you experience any difficulty during the installation or subsequent use
of a Kingston product, please contact Kingstons Technical Support department at either: (714) 435-2639 U.S.
headquarters, or Kingston Germany Office at (089) 62 71 56-21, prior, to servicing your system. This warranty
covers only repair or replacement of defective Kingston products, as provided above. Kingston is not liable for,
and does not cover under warranty, any costs associated with servicing and/or installation of Kingston products.

Disclaimers – The foregoing is the complete warranty for Kingston products and supersedes all other
warranties and representations, whether oral or written. Except as expressly set forth above, no other
warranties are made with respect to Kingston products and Kingston expressly disclaims all warranties
not stated herein, including, to the extent permitted by applicable law, any implied warranty of
merchantability or fitness for a particular purpose. In no event will Kingston be liable to the purchaser,
or to any user of the Kingston product, for any damages, expenses, lost revenues, lost savings, lost
profits, or any other incidental or consequential damages arising from the purchase, use or inability to
use the Kingston product, even if Kingston has been advised of the possibility of such damages.

Copyright© 1996 Kingston Technology Company. All rights reserved. Printed in the U.S.A. Kingston

Technology and the Kingston logo are trademarks of Kingston Technology Company.

Summary of Contents for DATA EXPRESS DE90


























Reviews: