TAKING A TEMPERATURE
Tap the ON/OFF button to turn on the thermometer. You will hear a beep when the thermometer is ready to take a
temperature. The thermometer will be ready for temperature taking when the screen shows three dashes.
Place the thermometer according to your desired reading location (under the base of the tongue, under the base of the
armpit, or with only the silver tip placed in the rectum).
A beep will indicate when the temperature measurement is successfully completed. Temperature readings typically
take 8 seconds.
The temperature reading will be shown on the illuminated display. A smiling face icon indicates that the temperature is
normal while a neutral or frowning face indicates a mild or high fever, respectively.
The thermometer will automatically turn off after 30 seconds of inactivity. The display will briefly flash OFF and it will go
blank. You can also press and hold the ON/OFF button for 2 seconds to power off.
1.
2.
3.
4.
5.
FEATURE
Resolution
Accuracy in Water Bath
Measurement Time
Memory Function
Out-of-Range Indication
Operating Ambient Temperature
Storage Temperature
Guarantee of Quality
Compatibility
Service Life
DESCRIPTION
0.1°F (0.1°C)
± 0.2°F (0.1°C), 89.6°F - 109.2°F (32°C - 42.8°C)
Regular mode: < 8 seconds
Full temperature history available on mobile device
Temperature Range: 89.6°F-109.2°F (32°C - 42.8°C). Thermometer
will display 'H' (High) if the temperature is above the operating range
59°F - 95°F (15°C - 35°C)
15% to 85% R.H. non-condensing
-13°F to +95°F (-25°C to +35°C) at R.H. up to 90% non-condensing and
95°F to 158°F (35°C to 70°C) at a water vapor pressure up to 50 hPa
Complies with ISO 80601-2-56, IEC 60601-1, EC 60601-1-2,
IEC 60601-1-11
For use with Apple and Android devices. Please visit
kinsahealth.com/phones
for the full list of supported devices.
5 years
Consult instructions for use
Storage temperature limitation
Manufacturer
Batch code
Catalogue number
Humidity limitation
Non-sterile
Caution
Do not use if product is broken
damaged, or open
Type BF applied part
Dust and water rating
NOTICE: This device complies with Part 15 of the
FCC Rules. Operation is subject to the following
two conditions: this device may not cause harmful
interference, and this device must accept any
interference received, including interference that
may cause undesired operation.
EXPLANATION OF SYMBOLS
Place
thermometer here
FIGURE 1
Placement for oral readings
Base of
Tongue
Heat
Heat
RELIABLE METHODS TO MEASURE TEMPERATURE
Body temperature is one of the most important indicators of illness and so it is important that
temperatures be taken accurately. Please follow these instructions for use closely.
Oral Use:
Place the probe tip well under the tongue in a heat pocket. See Figure 1 for correct placement.
Keep mouth closed while the temperature reading is being taken. A normal oral temperature is considered
97.0°F - 99.9°F (36.1°C - 37.7°C). A probe cover is suggested for oral use to prevent the spread of germs.
Discard the probe cover after taking a temperature.
Rectal Use:
If rectal temperature readings are recommended by your doctor, you may use a probe
cover. Insert the temperature probe into a probe cover. Insert the probe tip no more than ½ inch into
rectum. STOP if you meet any resistance. The sensing unit is on the very tip of the probe and there is no
reason to insert the tip deep into the rectum. Do NOT insert the probe past the metal tip. In general, a
normal rectal temperature is considered 97.5°F - 100.3°F (36.4°C - 37.9°C).
Underarm Use:
Wipe armpit with a dry towel. Place probe in armpit and keep arm pressed firmly
against the body. In general, a normal underarm temperature is considered 96.5°F - 98.9°F (35.8°C -
37.2°C).
CLEANING & STORING
Clean the probe before and after use with a damp, soapy cloth or by disinfecting with rubbing alcohol (70% isopropyl alcohol). Wipe dry
with soft cloth. DO NOT BOIL OR CLEAN IN DISHWASHER. This will cause the thermometer to no longer function and will void the
warranty. Do not wash the unit with any thinner or chemical solvent.
Do not store the device in direct sunlight or at high temperatures. If the thermometer has been stored in cold conditions, allow it to warm
to room temperature before attempting a measurement. Performance of the device may be degraded if device is operated or stored
outside of the stated temperature ranges.
REPLACING THE BATTERY
The QuickCare thermometer is powered by a single CR2032 coin cell. When the battery is low, the screen will display
"APP" and the Kinsa app on your phone will confirm a low battery. To replace the battery:
• Insert a coin into the groove on the battery cover to turn and open it.
• Remove the old battery and replace with a new one. Make sure the the battery is in the correct polarity
direction (positive side faces user).
• Close the battery cover.
Battery Life: More than 600 measurements or approximately 2 years if used every day.
CHANGING FROM FAHRENHEIT TO CELSIUS & VICE-VERSA
To change the reading units on your thermometer, press the ON/OFF button once to turn the thermometer on and then press the
ON/OFF button 2 more times in rapid succession. To change the units used in the app, click on the “Menu” icon and select “Settings”
icon. An icon will be displayed to indicate which mode the thermometer is in. Touch the icon to switch modes.
The equipment is suitable for use in domestic establishments and is tested to CISPR emissions Class B Group 1 as well a home
healthcare immunity criteria found in IEC 60601-1-2 Table 4, 6, and Table 9. During the IEC 60601-1-2 immunity tests performed
the thermometer will accurately measure temperature or display an error. QuickCare utilizes Bluetooth Low Energy (BLE),
which uses the 2.4 GHz ISM band. BLE operates between 2.402 and 2.480 GHz. QuickCare transmits less than -2 dBm effective
radiated power.To protect the environment, dispose of empty batteries at appropriate collection sites according to national or
local regulations. Keep out of reach of young children, elderly and pets. FCC WARNING: Changes or modifications not expressly
approved by the party responsible for compliance could void the user’s authority to operate the equipment.
DISPLAY
SITUATION / SOLUTION
Firmware update in progress.
Problem detected, check the app for details.
≥ 96.9°F (36.1°C) and < 100°F (37.8°C)
≥ 100°F (37.8°C) and < 102.6°F (39.2°C)
≥ 102.6°F (39.2°C)
1. On initial setup, pair the app with thermometer
2. Battery is critically low
3. Fever guidance available in app
4. Queued readings; sync to app ASAP
Err
Happy Face
[No Fever]:
Neutral Face
[Mild/Moderate Fever]:
Sad Face
[High Fever]:
APP
UPd
UNDERSTANDING YOUR THERMOMETER DISPLAY
FCC ID: 2AFEOQC1
CR20
32
