background image

Instruction Manual 

PT3600 

FM HANDHELD TRANSCEIVER 

 

We are very grateful for your purchasing 

  brand two-way radios produced by 

Shenzhen Kirisun Electronics Co., Ltd. 

We believe 

  two-way radio, which always incorporates the latest technology, can bring 

great convenience to your life and work. 

We also believe that the quality and function of 

  two-way radio can meet your 

demands for reliable communication. 
 

Instructional Icons   

This radio is not intended for use by general population in an uncontrolled environment. It is only 
for occupational use and only applied to work-related conditions. 
The radio must be only used by users, who are fully aware of the hazards of the exposure and who 
are able to exercise control over their RF exposure to qualify for the higher exposure limits. 
The following icons are available through this manual: 
 

Notice to the User: 

* Government laws prohibit radio communication without permission in government districts. 
* Illegal operation is subject to punishment by fine and/or imprisonment. 
* Refer service to the well-trained professional technicians only. 
 

Safety: 

It is important that the user is aware of and understands hazards common to the operation of 

any radio. 
 

Warning: 

.      Turn off your radio before entering any area with a potentially explosive atmosphere (where 
the air contains gas, dust and smog, etc.), such as while taking on fuel, or while parking at a 
gasoline service station. 
 

Attentions: 

Please comply with the following attentions to avoid fire, bodily injury and damage to the 

radio. 
* Long time transmitting or continuous working in high power mode will make the rear side of the 
radio generate heat. 
* Please do not disassemble or assemble the radio under any circumstance. 
* Please do not expose the radio to direct sunlight for a long time; do not place the radio near any 
heating device, either. 
* Please do not put the radio in extremely dusty, moist or dabbling places; do not place it on any 
unstable surface, either. 
* If the radio emits smoke or strange odors, turn it off and remove the battery from the radio and 
contact your local authorized Kirisun dealer without delay. 

Summary of Contents for PT3600
















Reviews: