Kirisun PT3600 Instruction Manual Download

Page: 14 / 15

The communication range is
too short.

* Make sure the antenna is well connected.
* Make sure the antenna is the original supplied one.
* Check if the battery power is in normal state.
* Ask your local dealer to adjust the squelch level.

9. Major Specifications

Model PT3600

136 – 174MHz VHF

Frequency (MHz)

400 – 470MHz UHF

RF power

4W(UHF)

5W(VHF)

Tx clusters and harmonics

< -70dB

Frequency stability

5ppm

Max. deviation

5KHz (W) /

2.5KHz (N)

Rx sensitivity

≤

0.18

Channel selectivity

> 60dB

Intermodulation >

60dB

Max. audio power

≥

1000mW

Channel number

16 (15 + S)

Power supply

DC 7.4V

External dimension

47mm

× 107mm × 33mm

Weight

225g (with battery and antenna)

10. Status Setting

(by the dealer)

Model: Serial No.:
1. Channel setting
Channel No.

Tx frequency

Rx frequency

CTCSS/DCS

Summary of Contents for PT3600
















Search results

Summary of Contents for PT3600

Reviews:

Related manuals for PT3600

Brands by name

Popular brands

Kirisun PT3600, Instruction Manual

Search results

Summary of Contents for PT3600

Reviews:

Related manuals for PT3600

Brands by name

Popular brands