background image

IMPORTANT NOTICE: 

DO NOT return to place of purchase !!! 
Please contact Customer Service hotline at 800-913-8999 for help 

 

 

LOCATING HEATER FOR USE 

 

 

BE CAREFUL

: When certain materials or items are left under this heater, while in use, they will be 

subjectok to radiant heat and could be seriously damaged.   

 

  The unit is designed for heating outdoor patios, decks, spas, pool and working areas. 

  Always ensure that adequate fresh air ventilation is provided. Follow the spacing tolerances in Figure 1.   

  The minimum clearances to combustible construction shown in Figure 1 must be maintained at all times 

  The installation must conform to local codes or in the absence of local codes with the standard for the 

storage and handling of liquid petroleum gases: 

In the US use : ANSI/NFPA58 on National Fuel Gas Code ANSI Z223-1998 

In Canada use: National Standards of Canada. CAN/CGA B149.1 & 2-M86 

  The heater must be placed on level firm ground. 

  Never operate in an explosive atmosphere.    Keep away from areas where gasoline or other flammable 

liquids or vapors are stored or used. 

Page9 

 

 

 

 

                                                                                                                                            36

” (91cm)

 

                                                 

 

                                               

36” ((91cm) 

W

ALL 

Figure 1.   

CELING / OVERHANG   

CAUTION 

 

 

 

 

 

 

 

 

 

During strong and windy weather, turn off the   

heater and the gas cylinder valve.    Remove   

the heater reflector hood then move the heater   

to a sheltered location.    Caution do not move   

heater while it is still hot.   

Summary of Contents for PTH106A-SS



















Reviews: