background image

LIMITED WARRANTY 

FOR MODEL PTH106A-SS 

GAS-FIRED INFRARED OUTDOOR PATIO HEATER 

 

Nexgrill Industries, Inc 

warrants to the original consumer purchaser of each Outdoor Patio Heater 

that when subject to normal residential use, it is free from defects in workmanship and materials 
under normal conditions of use in a commercial application for a period of 90 days from purchase 
and in a residential application for a period of 1 year.   Any work or repair of the heater must be 
performed by qualified service personal.  There will be a shipping and handling charge for the 
delivery of the warranty part(s). 
 

Component                                

    Warranty Period 

 

Burner:   

 

 

 

 

 

 

 

 

 

 

 

  3 Years 

Valve:                                                                                                 1 Year 
Pilot Kit:  

 

 

 

 

 

 

 

 

 

 

 

  1 Year 

All Other Parts                                                               

 

 

          1 Year 

 
Our obligation under this warranty is limited to repair or replacement at our option of the product 
during the warranty period. The extent of any liability of Nexgrill Industries, Inc. under this warranty 
is limited to repair or replacement. This warranty does not cover normal wear of parts, damage 
resulting from any of the following: negligent use or misuse of the product, use on improper fuel/gas 
supply, use contrary to operating instructions, or alteration by any person other than our factory 
service center.    The warranty period is not extended by such repair or replacement. 
 

Warranty claim procedure:   

If you require service or parts for your Patio Heater, please contact 

our Warranty Service Center for factory direct assistance. Our hours of operation are 8 AM to 5 PM 
PST. Our number is 1-800-913-8999 and our FAX number is 1-909-598-7699.  Please direct all 
correspondence to:  Nexgrill Industries, Inc

. 145 Brea Canyon Road, Walnut, CA 91789 ATTN: 

Warranty Service Center.

 

 
Product repair as provided under this warranty is your exclusive remedy.  Nexgrill Industries, Inc.

 

shall not be liable for any incidental or consequential damages for breach of any express or implied 
warranty on its products.    Except to the extent prohibited by applicable law, any implied warranty or 
merchantability or fitness for a particular purpose on this product to the duration of the above 
warranty.  Some states do not allow the exclusion or limitation of incidental or consequential 
damages or allow limitations on how long an implied warranty lasts, so the above limitations or 
exclusions may not apply to you.    This warranty gives you specific legal rights, and you may have 
other rights which vary from state to state.   
 

 

 

Page 17 

Summary of Contents for PTH106A-SS



















Reviews: