background image

9

INSTALLATION

INSTALLATION

Install the battery wand cover with the slot aligned to the socket in the battery wand.

Proceed to”Testing the Blind” on page 10.

If You Have an 18V DC Power Supply...

Connect the Power Supply

Plug the power cable from the blind into the extension cable. 

Plug the other end of the extension cable into the 18V DC Power Supply. 

Plug the 18V DC Power Supply into a standard outlet. 

Secure the extension cable using wire retainers (not supplied). If hiding the cable 
behind the blind, make sure it does not impede the operation of the blind.

Space the wire retainers approximately 15" apart along the power supply cable, as 
shown.

WARNING:  

Keep cables and small parts out of the reach of children. They can 

wrap cables around their necks and 

STRANGLE.

 They can also put small parts 

in their mouths and 

CHOKE.

WARNING:  

Electric shock and/or a fire hazard may occur, if not properly 

installed. 

Proceed to “Testing the Blind” on page 10.

If You Have an 18V DC Power Supply with Daisy-Chain Connections...

The daisy-chain feature allows up to three Tilt Automation blinds to be powered by a single 18V DC Power Supply. However, each 
blind has its own transceiver and can operate independently. The daisy-chain feature is only available with the 18V DC Power 
Supply option. 

Route the power cables from each blind through the connector, using an extension cable, if necessary. 

Plug an extension cable into the connector and the 18V DC Power Supply. A two-blind configuration is shown below. 

An additional connector and two additional extension cables are used for three blinds. 

Battery Wand Cover

Extension

Cable

Power Cable

from Blind

Power Cable

from Blind

Extension

Cable

18V 

DC

Power

Supply

15"

Maximum

Wire Retainers

Power Cable

from Blind

Extension

Cable

Connector

Summary of Contents for Alternative Wood Blinds Series




















Reviews: