background image

15

INSTALLATION

OPERATION

Cleaning

Wash the slats only using a non-abrasive mild detergent solution. Allow to air dry preserve the dust repellent properties of  
the slats. 

For a more thorough cleanings, alternative wood bottom rails and slats may be immersed in a bathtub. Bathtub cleaning is not 
recommended for blinds with decorative tapes. Do not immerse headrail.

IMPORTANT:  

Kirsch

®

 does not recommend ultrasonic cleaning of alternative wood blinds.

Window Blind Cord Can STRANGLE Your Child. 

Children can climb furniture to reach cords. Move crib and furniture away.

Keep all cords out of children’s reach.

Cord Connector

This component acts a s a stopper to prevent inner cords from being pulled through the blind, which can pose 
the risk of entanglement. 

It is also designed to break apart under pressure. 

Reassembly of Cord Connector

Reinsert any loose cords into the top notched of the 
cord connector. There is a notch on each side. 

Line up the two halves of the cord connector and snap 
the pieces back together. 

Cord 

Connector

Four

Cords

Two

Cords

WARNING

For more safety information, call 1-800-997-2389.

CHILD SAFETY

Summary of Contents for Alternative Wood Blinds Series




















Reviews: