background image

9

INSTALLATION

INSTALLATION

STEP 4:  Connect the Power Source

NOTE:  

When power is connected to the motor, a blue LED inside the control button housing will flash twice to indicate the shade 

is ready for operation.

 

Refer to the appropriate page based on your order.

 

For an optional attached battery wand, see below.

 

For a satellite battery pack, see page below.

 

For an optional headrail-mounted rechargeable battery wand, see page 10.

 

For an optional satellite-mounted rechargeable battery wand, see page 10.

 

For an optional 18V DC Power Supply, see page 12.

 

For two battery wands and a double connector power cable, see page 12.

 

For an optional 18V DC Power Supply with daisy-chain connections, see page 13.

 

For an optional C-size satellite battery wand or large DC supply, see the instructions that came with the wand.

Attached Battery Wand

Plug the Power Cable into the Battery Wand

 

Snap the battery wand into the battery wand clip on the back of the cassette.

 

Connect the power cable from the motor to the battery wand.

Proceed to “Testing the Shade” on page 13.

Satellite Battery Pack

 

Decide where you want to mount the bracket(s). A satellite battery pack may be mounted in any orientation.

 

Mark the screw holes.

 

Drill the screw hole using a 

3

32

" drill bit. 

 

Attach the installation brackets using the screws provided.

 

Position the battery wand or double connector power cable (if used) so the power cable is 
easily connected.

 

Snap the battery wand into the bracket.

Brackets removed for clarity.

Battery Wand

Battery Wand Clip

Power Cable

Bracket for the 

Satellite Battery Pack 

Socket

Summary of Contents for Banded Shade Automation III


























Reviews: