background image

10

INSTALLATION

INSTALLATION

 

Place the cover with its slot over the socket in the battery wand.

 

Plug the power cable from the shade into the extension cable. 

 

Plug the other end of the extension cable into the socket of the battery wand or double 
connector power cable (if used).

Proceed to “Testing the Shade” on page 13.

Headrail-Mounted Rechargeable Battery Wand

Insert the Rechargeable Battery Wand into the Battery Mount
NOTE:  

The rechargeable battery wand ships fully charged, so it is ready to install out of the package.

 

Match the direction of the arrow on the underside of the battery wand with the arrow on the battery mount.

 

Insert the nose of the battery wand into the cavity of the battery mount.

 

Push the battery wand flush into the mount until the battery snaps into place.

CAUTION:  

Failing to insert wand properly may cause it to fall out of the mount, posing an injury risk and potentially damaging 

the wand. Additionally, when mounting on a door, closing the door with excess force may cause battery wand to dislodge from the 
mount, also posing an injury risk and possibly damaging the wand.

Proceed to “Testing the Shade” on page 13.

Satellite-Mounted Rechargeable Battery Wand

 

Determine the location to mount the rechargeable battery wand.

CAUTION:  

To prevent overheating, 

do not

 install the rechargeable battery wand in direct sunlight.

 

The battery mount may be installed in any orientation.

 

Plan placement of the battery mount so that the cable can be plugged into the power socket. Allow at least 2" at the power 
socket end. 

 

Ensure the socket is within range of the cable.

CAUTION:  

Install the battery mount on a flat surface only. Installing on a round or other non-flat surface may result in the battery 

wand not attaching into the mount properly. This can result in either a failure to connect the shade to power or the wand falling 
out of the mount.

 

Mark the screw holes for the rechargeable battery mount.

Battery Wand Cover

Slot

Socket

Battery Wand Cover

Extension

Cable

Power Cable

from Shading

2"

Power

Socket

End

Allow 2" at power socket end for the extension 

cable jack. 

Minimum flat mounting area = 15" x 1" 

13"

15" Minimum Mounting Length

1"

Summary of Contents for Banded Shade Automation III


























Reviews: