background image

11

INSTALLATION

INSTALLATION

Testing the Shade

Use the control button to test the shade and ensure that the motor and power source are working correctly.

CAUTION:  

When raising the shade for the first time, observe how the 

fabric stacks. It should stack evenly. Immediately stop the shade if the 
bottom rail is not level or the shade starts to rub against either window 
jamb. See "Level the Rail(s), If Necessary" on page 16.

 

Press the control button on the bottom of the right-side end cap to test 
operation. If the shade does not operate, see "Troubleshooting" on page 
17

 

Press the button to alternately lower, stop, and raise the shade. 

 

The control button can also be used with the Automation App for advanced 
shade functions and home access. Open the app, press and hold the control 
button to see a list of available functions. See "Operating the Automation App and III Remote" on page 13

NOTE:  

With Top-Down/Bottom-Up and Day/Night shades, the control button will alternately lower the bottom rail, lower the 

middle rail, raise the middle rail, and raise the bottom rail.

Attach Magnetic Hold-Down Brackets (Optional)

Hold-down brackets provide stability and prevent swaying by securing the bottom rail, for example on French door applications. 
Hold-down brackets can only be used on outside mount shades.

STEP 1 — Bracket Placement

 

Place the magnetic hold-down bracket near one end of the bottom rail. The magnet should attract to the magnet that is 
already in the bottom rail.

 

Magnet Polarity:

  The magnet within the magnetic bracket must be attracted to the magnet located within the bottom rail. In 

the event that they repel each other, the magnet within the magnetic bracket can be removed and flipped.

 

To remove the magnet, hold a small steel flat blade screwdriver up to the magnet in the bracket and pull the magnet out 
with the screwdriver.

 

Flip the magnet over and place it back into the bracket.

IMPORTANT:  

Check the attraction prior to mounting to ensure that they are properly oriented.

STEP 2 — Mark the Location

 

Lower the shade to the closed position and mark the location where the bracket will be placed.STEP 3 — Attach the Bracket

Control 

Button

Front of

Shade

Summary of Contents for Cellular Shade Automation III

























Reviews: