background image

8

INSTALLATION

INSTALLATION

Mount the Headrail 

 

Tilt the headrail so that its back lip slides under 
the front lip of the end brackets and intermediate 
bracket(s).

 

Push the headrail against the back of the end 
brackets.

 

Check that the front lip of the intermediate bracket(s) 
is under the front lip of the headrail. 

Adjust the Headrail Tightness 

 

If the headrail is loose in the end brackets, bend the tabs on the end bracket outward. 

NOTE:  

The tabs may also be bent inward if the headrail is difficult to install into the end brackets. 

 

If your headrail end brackets do not have adjustable tabs, bend the tabs on the headrail end locks to 
adjust headrail tightness. 

Close the End Brackets

 

Push the cover down until it snaps over the locking tab on the bottom of the end bracket.

Open the End Brackets (If Necessary)

 

To open the end brackets, insert a flat blade screwdriver between the bottom of the cover and the quick 
release tab, and twist. 

 

You can also push up on the bottom of the end bracket to release the locking tab.

STEP 4 — Connect the Power Source, If Applicable

Refer to the appropriate page based on your order. 

 

For a headrail-mounted rechargeable battery wand, see”Testing the Blind” on page 11.

 

For a battery wand, see”Testing the Blind” on page 11.

 

For an optional rechargeable battery wand, see page 9.

 

For an optional 18V DC Power Supply, see page 10.

 

For an optional 18V DC Power Supply with daisy-chain connections, see page 10.

 

For any other Kirsch

®

 power supplies, see applicable instructions.

End Bracket

Intermediate Bracket

1

3

8

"

Slat Size

1

3

8

"

Slat Size

Summary of Contents for Wood Blinds Tilt Automation III























Reviews: