14
7
13
3−1 Specifications table
3 . Specifications
4 . Hydraulic Oil
Table 2
Thru-hole diameter
Piston stroke
Piston surface area
(pulling side)
Piston maximum
thrust force
Maximum operating
hydraulic pressure
Maximum
rotation speed
Mass
Moment of inertia
Drain amount
Balance quality
Storing temperature /
Operating temperature
mm
mm
cm
2
kN
MPa
min
-1
kg
Kg・m
2
／min
Note 1) The drain amount is a value when the hydraulic pressure is 3.0 MPa, and the oil temperature is 50℃.
Note 2) How to obtain the piston thrust force
Note 3) When storing this product, the product should be subjected to the antirust treatment and stored in a place
free from wetting, condensation, or freeze.
○To keep good operation of the cylinder, it is recommended to use hydraulic oil with a viscosity of 32cSt at 40℃. (ISO
VG32 equivalent product)
○Replace the hydraulic oil about once every six months.
○The characteristics of hydraulic oil influences the heating, drain amount and acting speed of the cylinder, therefore,
control it according to the instruction manual for the hydraulic unit.
Operating
Piston
thrust force
(kN)
・If high speed rotation is continued, the oil temperature will rise, which could rapidly a high temperature, it will
rapidly aggravate deterioration of the sealing materials and deterioration of the hydraulic oil. Use a cooler to keep
the oil temperature at 60℃ or lower.
留 意
・Turn off the power source and supply designated hydraulic oil. Insufficient oil supply decreases the acting speed,
causes thrust force insufficiency resulting in a drop in the chuck gripping force, which could allow the work to fly out.
Use abrasion resistant and deforming hydraulic oil. Add a filter of 20?m or less in the pressure supplying line(P)
to maintain the function of the cylinder and to prevent seizing caused by foreign matter.
Safety information about hydraulic fluid and anti-rust oil
Applicable range
・Hydraulic fluid sealed in the product at the delivery.
・Antirust agent applied to the product at the delivery.
First aid measures
After inhalation: Remove victim to fresh air. If symptoms persist, call a physician.
After contact with skin: Wash off with mild cleaners and plenty of water. If symptoms persist, call a physician.
After contact with eyes: Rinse with plenty of water. If symptoms persist, call a physician.
After ingestion: If large amounts are swallowed, do not induce vomiting. Obtain medical attention.
・Please refer to each MSDS about the hydraulic fluid and the anti-rust oil which you prepared.
Piston
Maximum
Thrust force
(kN)
Operating
hydraulic pressure(MPa) −0.25
Maximum operating
hydraulic pressure(MPa) −0.25
＝
×
WARNING
NOTICE
36
15
64
24
4.0
8000
8.6
0.011
3.0
46
15
89
33
4.0
7000
12.0
0.019
3.0
52
22
150
56
4.0
6200
16.8
0.053
3.9
75
25
183
69
4.0
4700
26.0
0.095
4.2
91
30
234
88
4.0
3800
33.0
0.153
4.5
165
30
332
91
3.0
1700
84.0
0.698
8.4
46
32
89
33
4.0
7000
12.8
0.022
3.0
52
34
150
56
4.0
6200
17.0
0.058
3.9
75
40
183
69
4.0
4700
26.8
0.100
4.2
Type
S1036 S1246 S1552 S1875 S2091 S2816 S1246L S1552L S1875L S2091L
91
50
234
88
4.0
3800
34.1
0.160
4.5
G6.3
−20〜＋50℃ ／−10〜＋40℃
※ Keep the back pressure extremely low in this case as well.
＜Example＞
Chuck open and close
Cooler
To cylinder A. B. port
Inside and outside diameter
gripping switching
Fig. 4
Summary of Contents for S1036
Page 31: ......
